Introduzione
Questa guida ti mostrerà come rimuovere e sostituire la batteria del Samsung Galaxy S20.
La batteria è tenuta ferma con dell'adesivo. È necessario dell'alcool isopropilico ad alta concentrazione (maggiore del 90%) per ammorbidire l'adesivo.
Se la tua batteria è gonfia, prendi le dovute precauzioni e non scaldare il tuo telefono.
Per la tua sicurezza, scarica il telefono al di sotto del 25% prima di smontarlo. Questo ridurrà il rischio di eventi termici pericolosi se la batteria viene accidentalmente danneggiata durante la riparazione.
Avrai bisogno di adesivo sostitutivo per portare a termine la riparazione.
Cosa ti serve
-
-
Scalda un iOpener e applicalo sul lato basso della cover posteriore per due minuti.
-
-
-
Applica una ventosa sul retro del telefono, il più vicino possibile al centro del bordo inferiore.
-
Tira la ventosa con forza costante, per formare un'apertura tra la cover posteriore e la cornice.
-
Inserisci la punta di un plettro nell'apertura.
While pulling on the back glass with the suction cup, I found it helpful to use something like the opener tool to press down on the frame. Made it easy to pull open even with the iOpener.
-
-
-
Applica l'iOpener scaldato sul lato sinistro della cover posteriore per due minuti.
-
-
-
Applica una ventosa sul retro del telefono, il più possibile vicino al centro del bordo sinistro.
-
Tira la ventosa con forza costante, per formare un'apertura tra la cover posteriore e la cornice.
-
Inserisci la punta di un plettro di apertura nella fessura.
-
Puoi anche provare ad applicare alcune gocce di alcool isopropilico nella fessura per aiutare ad ammorbidire l'adesivo.
-
-
-
Applica un iOpener scaldato sul lato destro della cover posteriore per due minuti.
-
-
-
Applica una ventosa sul retro del telefono, il più vicino possibile al centro del lato destro.
-
Tira la ventosa con forza costante, per formare un'apertura tra la cover posteriore e la cornice.
-
Inserisci la punta del plettro nella fessura.
-
-
-
-
Applica un iOpener scaldato sul lato superiore della cover posteriore per due minuti.
-
-
-
Fai passare gradualmente il plettro dal lato destro del dispositivo intorno all'angolo in alto a destra.
-
Continua a far scorrere il plettro sul lato superiore fino all'angolo in alto a sinistra per separare completamente l'adesivo della cover posteriore.
-
-
Attrezzo utilizzato in questo passaggio:Tweezers$4.99
-
Alza la cover posteriore lentamente. Usa i plettri e passali dove è rimasto ancora dell'adesivo.
-
Rimuovi la cover posteriore.
-
Questo è un ottimo momento per accendere il tuo telefono e testare tutte le sue funzioni prima di sigillare la cover posteriore. Controlla che il tuo telefono sia spento prima di continuare a lavorarci.
-
Rimuovi eventuali pezzi di adesivo con un paio di pinzette o con le dita. Applica calore se stai avendo problemi nel separare l'adesivo.
-
Se stai usando degli adesivi pretagliati, segui questa guida.
-
Se stai usando il biadesivo, segui questa guida.
-
-
Attrezzo utilizzato in questo passaggio:Magnetic Project Mat$19.95
-
Usa un cacciavite a croce Phillips #00 per rimuovere le cinque viti da 4 mm che tengono fissato il supporto della scheda madre.
-
-
Attrezzo utilizzato in questo passaggio:Tweezers$4.99
-
Usa un paio di pinzette per tirare gentilmente verso l'alto e sganciare il supporto della scheda madre dal telaio intermedio in plastica.
-
-
-
Separa delicatamente la bobina di ricarica wireless dal dispositivo.
-
Rimuovi la bobina di ricarica wireless
-
-
-
Utilizza uno spudger per far leva e disconnettere il connettore della batteria.
-
-
-
Usa un cacciavite a croce Phillips #00 per rimuovere le cinque viti da 4 mm che tengono fissato l'altoparlante e il telaio centrale inferiore.
-
-
Attrezzo utilizzato in questo passaggio:Tweezers$4.99
-
Inserisci la punta di uno spudger o un paio di pinzette nell'incavo nell'angolo in alto a sinistra del telaio centrale e fai leva per rilasciare i ganci che lo tengono in posizione.
-
Rimuovi l'altoparlante inferiore e il telaio centrale inferiore.
-
-
-
Usa uno spudger per sollevare e scollegare i cavi a nastro principali e ausiliari dalla scheda figlia vicino al bordo inferiore del dispositivo.
-
-
-
Usa uno spudger per sollevare e scollegare i cavi a nastro principali e ausiliari dalla scheda madre.
-
-
-
Solleva e rimuovi delicatamente i cavi a nastro principali e ausiliari.
-
-
-
Usa uno spudger per sollevare e scollegare il cavo a nastro principale dello schermo dalla scheda madre.
-
-
-
Solleva e piega delicatamente il cavo a nastro dello schermo lontano dalla scheda madre e dalla batteria.
-
-
-
Applica 1-2 gocce di alcool isopropilico ad alta concentrazione (maggiore del 90%) sul bordo superiore della batteria.
-
Attendi due minuti per permettere che l'alcool isopropilico ammorbidisca l'adesivo.
-
-
-
Posiziona una ventosa al centro della batteria.
-
Tieni la parte superiore e inferiore del dispositivo contro la superficie di lavoro con una mano e tira con decisione la ventosa con l'altra.
-
L'adesivo richiede tempo e tiri continui anziché una forza eccessiva per allentarsi. Tira la ventosa con forza costante per 15 secondi alla volta.
-
Se la batteria non si allenta, applica 1-2 gocce di alcool isopropilico lungo i bordi superiore, sinistro e destro, aspetta un minuto e tira di nuovo.
-
Quando la batteria comincia a staccarsi dal dispositivo, procedi al passo successivo.
-
-
-
Inserisci uno plettro di apertura sotto il bordo inferiore della batteria e giralo per allentare l'adesivo.
-
-
-
Rimuovi la batteria.
-
Stacca e/o rimuovi l'adesivo rimanente prima di cominciare la pulizia dell'incavo dove risiedeva la batteria. Per fare ciò utilizza dell'alcool isopropilico e un panno privo di lanugine.
-
Se hai utilizzato alcool isopropilico, aspetta dieci minuti prima di installare la nuova batteria per permettere all'alcool di evaporare completamente.
What is the piece behind the battery that looks like its circled called? Is it normal to see this piece when shining a flashlight onto the screen when the phone is off?
That’s the fingerprint sensor! Because it’s embedded in the screen, if you shine a light behind it, you can see it through the front glass.
-
Confronta la parte nuova con quella originale, potresti aver bisogno di spostare alcuni componenti rimanenti o rimuovere il supporto dell'adesivo prima di installare la nuova parte.
Per rimontare il dispositivo, segui le istruzioni in ordine inverso.
Segui questa guida per eseguire un ripristino del ciclo della batteria, e calibra la tua nuova batteria appena installata.
Porta i tuoi rifiuti elettronici a un riciclatore certificato R2 o e-Stewards.
La riparazione non è andata come pianificato? Dai un'occhiata alla nostra comunità Risposte o la wiki per la risoluzione dei problemi per trovare aiuto.
Confronta la parte nuova con quella originale, potresti aver bisogno di spostare alcuni componenti rimanenti o rimuovere il supporto dell'adesivo prima di installare la nuova parte.
Per rimontare il dispositivo, segui le istruzioni in ordine inverso.
Segui questa guida per eseguire un ripristino del ciclo della batteria, e calibra la tua nuova batteria appena installata.
Porta i tuoi rifiuti elettronici a un riciclatore certificato R2 o e-Stewards.
La riparazione non è andata come pianificato? Dai un'occhiata alla nostra comunità Risposte o la wiki per la risoluzione dei problemi per trovare aiuto.
Annulla: non ho completato questa guida.
Altre 29 persone hanno completato questa guida.
Un ringraziamento speciale a questi traduttori:
100%
Questi traduttori ci stanno aiutando ad aggiustare il mondo! Vuoi partecipare?
Inizia a tradurre ›
25 Commenti
I had a huge amount of difficulty removing the battery during this repair. The adhesive is really strong, the suction cup doesn't stick to the battery very well and if you lever it out you run the risk of puncturing the battery. It's also really difficult to pull up on the battery while holding the phone down, especially because you want to avoid touching the circuits.
Eventually I succeeded and everything seemed to work but the next day the phone wouldn't switch on. I think maybe the adhesive remover got somewhere it shouldn't have. If I could add something to this guide, it would be "once battery is removed, allow phone to sit for 30 mins to ensure all adhesive remover has evaporated". If I was allowed a do-over I would try to heat the adhesive instead. Or use the string trick. I'm switching to an iphone now because apparently they don't glue their batteries.
Good point! I would suggest to use pure isopropyl alcohol and not something below 99%. The residual water might be not much but still there is a slight chance of it getting somewhere inside. Also the 99% pure alcohol evaporates much faster and leaves no traces. Apple batteries are also glued in with adhesive. What apple does right are the pull-strings to remove the sticky tape between chassis and battery.
Followed every step and managed to complete it but after a couple of minutes the phone screen stopped working and turned black.
I'm pretty sure that happened because the isopropyl alcohol went through the phone into the screen through the gap right under where the battery seats.
If you attempt this at home be aware this might happen, so disconnect the display too or look into using a different method for removing the battery.
I don't think this repair is worth attempting. I also killed my screen with this one, similar to the two commenters above. Whether it was isopropyl alcohol getting into the LCD or whether it was some issue with flimsy connectors I don't know. I was super careful and I've still bricked it, so I'd rate this repair as 'too risky'.
i typically use an iPlastix opening tool, a heating pad and lots of alcohol, get the very tip of the opening tool to sort of bend or roll into a curve, then slip the bent tip into the gap between frame and battery dripping some alcohol onto the tool, eventually you can get the rolled end to slip underneath the battery. then just slide the tool around the perimeter of the battery, cutting the adhesive, eventually, once all the adhesive is cut the battery will easily pry out of the phone. continually apply alcohol to the surface of the tool once you get the curved end under the battery, the alcohol will drip down the tool and find its way under the battery more easily weaking the adhesive.
since the tool is made of plastic, its almost impossible to scratch, bend or puncture the battery during the removal process by using this method, this is also my preferred method for removing bulged batteries that a suction cup wont stick to, or batteries where putting any unnecessary pressure could cause them to burst.
As with other comments, battery swap went fine, but after a bit of use I connected the phone to a charger and screen went black. Strange experience, feels like it's booby trapped.
I used this repair guide to change my battery in my S20. All went well and successfully especially after using this guide. IPA helped massively to remove the battery but I DO NOT RECOMMEND USING IT. i read the comments about the screen going blank etc. i used a heat gun to evaporate the IPA before reassembling the device thinking this would eliminate any issues. I WAS WRONG. DO NOT USE IPA to remove the battery. I turned my phone back on ant it was okay for a few minutes. Then the screen started flickering and turned completely green then went black. The phone still works as i can hear the notification sounds etc but no screen. Again DO NOT USE IPA TO REMOVE BATTERY
When the alcohol gets into the screen, the screen becomes black, it dies. Do not try this guide.
Did this repair to a T, it killed my display about 30 mins later. DONT USE IPA
I even used my heat gun to evaporate all of it off, let the phone sit for an hour too. still killed it!
Hi Bradley,
I'm really sorry to hear of your repair experience. I think the IPA may have seeped through the fingerprint sensor cutout and into the OLED panel.
When the battery adhesive is still intact, it should seal against moderate use of IPA along the top and side edges. I looked over the guide and changed the wording to give clearer guidance and warnings on how much to apply, where to apply it, and when not to use IPA.
Is there any procedure needed to reset the battery stats or charging levels? I replaced without problem but my battery life is not as good as my old battery! Wondering if there is a step on the software side?
Did you figure it out? I have the same issue. Looks like an original battery, but batt life is weak and Samsung Members diagnostics shows battery needs replacement...
Slawek -
The screws are more likely to be #0 JIS rather than #00 Phillips. Certainly my JIS screwdriver fits much better than my Phillips one.
I haven't had a problem with IPA use yet, but the battery adhesive is stupidly strong. Just use a mechanical clip, Samsung. My Blackberry is: slide back off, lift up battery, insert new battery, slide on back cover. Probably five seconds. Things weren't so bad in the 2010s.
The Samsung battery reset app doesn't recognise the QR code on the packaging so far.
As well i killed my screen, i turned up and and worked a few minutes, later I left it charging, and when I came back the screen was completely black, I plug it to my monitor, and the phone is still working but no the screen. Anyway his method did not help me to remove the battery
After all these comments concerning a screen-blackout after using alcohol I didn't dare to use that. Just pulled with the suction handle and pried with different tools from the bottom. That took a lot of time, sweat, fear to break the battery and quite some force. Why do manufacturers glue in the batteries?!
Worked out fine and I'm happy with the new battery.
why does it needs to be below 25%? I understand it being at maximum 60%, but for what I learned Li-ion batteries are unstable at 0% too. Maybe it needs to be better specified?
Toller Guide!
War mein erster Akkutausch.
Statt dem Alkohol hab ich aber den Akku bzw Kleber mit einem Föhn über die Displayseite erwärmt. Hat wunderbar funktioniert.
Klebereste hab ich dann mit 2 Tropfen Desinfektionsgel und nem Wattestäbchen gelöst. Rückbau hat auch ohne Probleme funktioniert.
I completed the swap without affecting the screen. To avoid killing the screen as others have done, I used 2 tiny drops of acetone from a needle behind the battery then applied constant even pressure to the battery over a long period of time. If you do not have a way of getting the solvent accurately only onto the glue, use the constant pull method alone. Be careful about putting tools behind the battery as there is an area behind the battery with a soft membrane.
I completed the swap without obvious issue. However if I unplug the phone from a charger it immediately turns off as if there is no battery at all. I re-opened the phone and disconnected and reconnected all the upper and lower flex cable connectors carefully. This did not resolve the issue. The battery shows 4000 mAh at 100% or 99% charge when connected to USB and powered on. I don't know if there is something I am missing of if I possibly revived a bad replacement battery.
Thanks for this informative instruction manual. What I would like to ask is, where can I find a genuine S20 battery?
Found that using the iOpener did not provide enough heat to weaken the adhesive, went with a hairdryer instead. Make sure to never keep the hairdryer still, and apply heat on high for 30 seconds to 1 minute per side did the job for me. iOpener just did not get hot enough
Phil R - Replica