Wiki con Collaborazione Studenti
Un fantastico team di studenti del nostro programma educativo ha realizzato questo wiki.
Low Battery
I want to hear sound clearly on both the parent and the baby monitors, but the sound is coming in and out and it is unclear. Also, the parent unit beeps twice every 30 seconds.
Power on, power off
Try to power off the device by pressing the power button and turn it back on to see if it will continue working properly.
Replace the battery
Your batteries may be low. If the battery is low, replace the battery and the sound should produced from the parent unit will be consistent.Connect to AC power if the batteries are properly installed into the parent unit, but the POWER/LINK light on the parent unit is off.You can choose to power the parent unit by connecting it to AC power.
Monitor making high-pitched sound
The baby monitor keeps making this high-pitched noise
Monitor out of range
The monitor’s may be too far apart from each other. Try to get closer to the other monitor. If this does not help, try to adjust the sensitivity level.
Need to adjust sensitivity level
Try to adjust the sensitivity level to a lower level to avoid audio feedback.
Monitors may be too close
The monitors have to be more than three feet away from each other. Try backing up from the monitor to get rid of noise. If this does not work, try adjusting the sensitivity level.
Two Monitors Not Linking
I want to be able to give and receive audio, but the monitors are failing to keep a connection.
Monitors Not Turned On
Press and hold the power button for 2 seconds to turn on the baby monitor. Repeat the same process for the parent monitor until the screen display lights up.
Monitors Not Within Range
Move the parent monitor closer to the baby monitor, but do not get closer than 3 feet from the baby monitor.
Monitors Need to be Reset
Reset the monitors by turning them off and unplugging them from their electrical power. Wait 15 seconds and then plug them back in again. Turn on the monitors and allow up to a minute for the monitors to synchronize.
Unresponsive Screen
I want to use my baby monitor’s screen but the screen isn’t responding to my commands.
Low Batteries
You batteries may be low. The battery icon light and LOW BATTERY will flash on the parent unit. If this is so, replace the battery.
Monitor is out of range
Make sure the monitors are within range of up to 1000' of each other. If not, move the monitors closer together.
Monitor is Not On
Press the power button located in the middle of the parent device.
Minor Glitches
Your monitor may be glitching. Try rebooting it by pressing the power button once to turn it off and once again to turn it back on.
Team
USF Tampa, Team 1-5, Leahy Fall 2015 Membro di USF Tampa, Team 1-5, Leahy Fall 2015
USFT-LEAHY-F15S1G5
4 Membri
5 Guide realizzate
40 Commenti
I have bought three sets of baby monitors and they all keep cutting on and off please what can be affecting them
carolinemclaughlin - Replica
Mine won't turn on or off, the Link and the battery light are both on, whether it's plugged in or not, and the screen is totally blank, with no sound coming through.
celia - Replica
This just happened to my monitor, were you able to fix yours??
Jaimie Brydges -
Our baby Monitor keeps saying no link to camera 1, which is not true, or that we are out of range when we are less than 20' away. What gives..
jonlewis55 - Replica
Ours is doing the same thing and can't figure out why. It's driving me nuts
dalycia -
Any answer to this? Same problem here
BRANDON GORLEY -
I'm having the same issue and when it does link the feed is delayed and jumpy
PEbert -
We are having the same issue, any resolution available?
Katie Kanaskie -
Same here and it keeps glitching.
crawfordjacqueline28 -
When on night vision it keeps going to a dark screen then back tonight vision
soniasaunders - Replica
Having the same issue. Any resolution?
Joe LaBella -
For what it is worth, I have been having the same problem for weeks with the monitors not linking. I just had an idea this evening so I tested my theory. I reset my Internet router and while it was off the monitors worked great. Once the router was back on the monitors had troubles again. I changed the channel of the router and things seem much better.
No guarantee this will work for everyone but maybe it will work for somebody.
Brad V - Replica
I've had the Vtech for less than a year. It worked fine and now...it does not work at all. After a few seconds, the sound goes (though it visually seems to be recording sound still) and then the screen goes black. It is fully charged. I've reset the wifi. Yet, all that still shows the receiver works is the green flashing sound blips. I can turn it on and off again. And start the whole process over. Baffled for what it cost and the positive reviews I had read until coming to this "troubleshooting" page.
Hillarie Higgins - Replica
No link to camera 1, Beep! Beep! Beep! Beep! Turning out to be a waste of money. All I want to do is keep an eye on my daughter.
Kat Majesta - Replica
My device did the same. Do you have a wireless home phone or wifi? The baby monitor transmits on the same frequency and when the devices are close to each other to cause interference to each other. Internet is slowed and monitor loses signal. In the future I will be more diligent in how I choice my wireless devices when frequency is an issue. Hope that helps. I ended up using a hardwired system and used Bluetooth to connect it to my cell phone.
Nabil Alhadi -
Had mine for a year. Now it seems like the “talk” button is sticking on the parent unit. I’m not hearing any noise then I press and let go of the button. I get noise for a few seconds and then stops again.
AnnMarie Turner - Replica
Same issue hear
aboriginal -
Any luck on this? Mine is doing this to
Nicole Graham -
Same issues 😪 please any positive feedback much appreciated on a fix for this
Sarah -
One monitor is picking up another monitor. Instead of the receiver.
John Hayes - Replica
My monitors seem to time out when panning rooms. It will show that it is switching cameras in the top left but wont actually switch, any ideas?
Katie - Replica
The baby unit of my monitor set refuses to come on, even though it’s plugged in. What can I do? Anyone else have this problem?
Melissa Alford - Replica
My baby monitor keep saying rmid what’s does that mean and why won’t it connect it used to work perfectly
chris evans - Replica
When I have the baby monitor on it will flash black then go back on. It will keep doing it on & off with just the picture but I can hear everything still. What is wrong with it. Can I fix it in anyway? Thank you
Brittney Schiebel - Replica
I am having similar issues. My monitor will be on for a few seconds then will fade to black then back on again. Not sure how to fix it either.
Amy Potter -
We just had it on for the first time last night.. it completely glitches out.. makes a clicking noise.. the battery and power buttons were flicking n tripping out.. it was plugged in.. we unplugged it kept doing it.. it randomly stopped after like 10 mins.. this all happened at 3am
Juliana Walker - Replica
I just bought a set of monitors today … and it keeps cutting in and out like there is a poor connection and I’m in range of like 10 feet away at max ! Not very happy for the price I paid
jacqueline.hines - Replica
Parent unit making beeping sound
One of the parent units is making beeping sound, intermittently. It will beep about 10 times; then stop. But, it will do it again later. What could be the problem?
Student14 - Replica
Hello
We have recently purchased vtech D221
The main walkie has the constant crackling noise
Tried reducing the sensitivity and alerts have been tested at all levels.
Batteries are perfect and both the equipments are well separated.
Suggestions appreciated
vishalasar - Replica
Our baby monitor keeps dropping the sound. It starts back up again after I change the volume or turn it off. However, it goes silent again About a minute after. How do I fix this?
aboriginal - Replica
Screen keeps going black on and off every few seconds sounds off and on when screen comes back on????
crystalbaugher32 - Replica
I have a problem in my VTech monitor owl .. when i turn on the watching screen.. the camera looking a green video living.. I don’t know how can I fix it .. The camera isn’t clear ☹️
hajarnasser_20 - Replica
mine keeps saying vtech cares about your baby. Install at least 3 feet away and make sure the cord is out of reach
Claudette H. - Replica
How do I cut WiFi off?
Macayla Ray - Replica
The screen is not clear it's kinda fuzzy how can I make it clear?
lisasayers59 - Replica
Ok just got out box worked 2 minutes as I was using it to make sure can see Babylon screen.. now the video isnt coming on keeps beeping what a load of crap bloody rip off my first born had a cheap one no prpbleme this is terrible espeshislly for the price shocking could it be faulty and I've lost my receipt so can I even return it ?!
kcb-3510x - Replica
My baby monitor keeps making a wind noises tho the camra screen
jadecowell1997 - Replica
No good answers here. My monitor is within range, new batteries and still no sound for over 65seconds.....!!!
Diane Whiteman - Replica
The 2 parent monitors do not link up and I have tried the suggested the tips to cure the problem but they still both show not not linked are there any other suggestions please
Derek - Replica
dm221 keeps saying not linked, tried every thing- off and on, battery charged to max. they are about 25ft from one room to other. We working fine, put away and now trying use them wont link to each other. 407.758.2506
Theresa Wadsworth - Replica