Salta al contenuto principale
Harman Kardon Onyx Studio 2 Control Board Replacement

Harman Kardon Onyx Studio 2 Control Board Replacement

Alexandra Achtenberg

Alexandra Achtenberg e un altro collaboratore

Ultimo aggiornamento il May 5, 2021

10 - 20 minuti
Facile

Introduzione

Vai al passo 1

If the buttons on your device aren't working, it may be time to replace your control board. Follow this guide to do so.

Cosa ti serve

Strumenti

Mostra di più…

  1. Harman Kardon Onyx Studio 2 Control Board Replacement, Front Panel: passo 1, immagine 1 di 3 Harman Kardon Onyx Studio 2 Control Board Replacement, Front Panel: passo 1, immagine 2 di 3 Harman Kardon Onyx Studio 2 Control Board Replacement, Front Panel: passo 1, immagine 3 di 3
    • Using a plastic opening tool, pry off the front grill by wedging it in the notch on the front of the device.

    Where can I find a new front panel for my speaker

    consomme69 - Replica

    If I take this off can I put it back on

    Burger King - Replica

  2. Harman Kardon Onyx Studio 2 Control Board Replacement: passo 2, immagine 1 di 2 Harman Kardon Onyx Studio 2 Control Board Replacement: passo 2, immagine 2 di 2
    • Remove the five 14.4 mm T10 Torx screws.

    There are NO torxscrews. You have to pull out the rubber grille grips that are inside the screw holes FIRST, then use a regular sized Phillips head screwdriver to remove the cover. No Torxscrewdiver needed. I found this out after I had already purchased one from you guys.

    phillip columbus - Replica

    Mi bocina no tiene los 5 tornillos a la vista,tiene las cavidades ciegas, como lo abro???

    Eduardo Heine - Replica

    Yes there are no Torx screws… you have to remove the rubber grips them the Philip Screws..

    Joe Lim - Replica

  3. Harman Kardon Onyx Studio 2 Control Board Replacement: passo 3, immagine 1 di 1
    • Gently pull the front apart from the back.

  4. Harman Kardon Onyx Studio 2 Control Board Replacement: passo 4, immagine 1 di 2 Harman Kardon Onyx Studio 2 Control Board Replacement: passo 4, immagine 2 di 2
    • Remove the four wires connecting the front and back panels.

    • Pinch the connector tab and pull gently upwards.

    • Repeat for the other three connectors.

    Please can I get a replacement of my panel to the phone

    Chinedu Ogunedo - Replica

  5. Harman Kardon Onyx Studio 2 Control Board Replacement, Control Board: passo 5, immagine 1 di 1
    • Pull the silicone button band off of the outer edge of the speaker.

  6. Harman Kardon Onyx Studio 2 Control Board Replacement: passo 6, immagine 1 di 2 Harman Kardon Onyx Studio 2 Control Board Replacement: passo 6, immagine 2 di 2
    • Disconnect the two pressure connections from the circuit board.

  7. Harman Kardon Onyx Studio 2 Control Board Replacement: passo 7, immagine 1 di 2 Harman Kardon Onyx Studio 2 Control Board Replacement: passo 7, immagine 2 di 2
    • Gently remove the control board band by placing fingers in contact with it through the button openings.

    • Work from the outer edges in so as not to bend the band.

    From where to buy Control panel

    ali - Replica

    From where to buy this control panel

    ali - Replica

    My speakers control board band broke. If possible, where can I find replacement?

    Abraham Lepez - Replica

Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 4 persone hanno completato questa guida.

Team

USF Tampa, Team 16-5, Blackwell Spring 2017 Membro di USF Tampa, Team 16-5, Blackwell Spring 2017

USFT-BLACKWELL-S17S16G5

3 Membri

24 Guide realizzate

9Commenti sulla guida

Do you guys know where to get a control board, because my board is broken so i am looking for one

Zhou Yuqi - Replica

Where to get control board onyx 2.

Mike Champagne - Replica

My on/off button keeps blinking…..would somebody please email me cause I am a techno nitwit……..i’m gonna bring this piece of non chargeable crap outside and go Italian on it with the 12 gauge! SERENITY NOW!

Sincerely,

email ; jorcal3318@aol.com

Frank Vitolo - Replica

power button continually blinks. Won’t turn on, can’t pair, no other action can be taken, just the blinking power button. what’s the solution? Please share….

rachael friesen -

Speaker plays for split second then fades away like wtf

Paul Berrellez - Replica

Speaker comes on loud then Fades away like the volume is stuck on low

Paul Berrellez - Replica

My volume button is not working,cant raise the volume on my speaker. And the volume is turned all the way down! Please help

Joseph Hernandez - Replica

Hi I have a problem with my control board

The volume will auto smaller and smaller until it's mute

Any idea to fix it or buy a replacement part?

And I want to buy replacement battery ,any stock available?

My email

Leoyu.leoyu@gmail.com

leoyu.leoyu - Replica

My Bluetooth connection button is not working

Joseph Bush - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 2

Ultimi 7 Giorni: 5

Ultimi 30 Giorni: 41

Tutti i Tempi: 14,965