iBook G3 Clamshell Modem Replacement

iRobot e 3 altri collaboratori

Ultimo aggiornamento il July 18, 2016

Nessuna stima

Moderato

Introduzione

Vai al passo 1

56k internal modem, standard on all models.

Cosa ti serve

Ricambi

Strumenti

Mostra di più…

Passo 1 Battery

iBook G3 Clamshell Modem Replacement, Battery: passo 1, immagine 1 di 1

Use a coin to turn both battery locking screws 90 degrees to the left.
Remove the battery cover.
Remove the battery from the computer by pulling up on the plastic tab.

Traduci

Passo 2 Airport Card

iBook G3 Clamshell Modem Replacement, Airport Card: passo 2, immagine 1 di 1

Pull the keyboard release tabs toward you and lift up on the keyboard until it pops free. Note that the keyboard ribbon is still attached to the logic board, so you cannot completely remove the keyboard yet.
If the keyboard does not come free, use a small flathead screwdriver to turn the keyboard locking screw (between F4 and F5 key) 180 degrees in either direction and try again.
Rotate the keyboard away from the screen and rest it face-down on the trackpad area.

Traduci

Passo 3

If your computer does not have an airport card, you can skip the next two steps.
Grasp the clear plastic tab on the airport card and pull up and toward the display.

Traduci

Note to those who want to install an airport card to a laptop here that doesn't have a card. The proper orientation is with the bar code facing up, and the "Airport" artwork and logo facing down. There are small slots on the bottom of the card that fit into pins below the trackpad. You will know it is properly slotted because the top of the card will touch the handles of the RAM shield.

The proper orientation of the antenna is that it is plugged in from the right side of the top of the airport card, with the cable winding up from the right to the left.

Marissa Stardance - 10 ott 2023 Replica

Passo 4

Hold the airport card in one hand and use your other hand to remove the antenna cable.

Traduci

Passo 5 Keyboard

iBook G3 Clamshell Modem Replacement, Keyboard: passo 5, immagine 1 di 1

Remove the two Phillips screws that secure the RAM shield.

Traduci

Passo 6

Grasp the wire metal bracket on top of the RAM shield and pull upward to remove the shield.

Traduci

Passo 7

Pull up the keyboard connector cable by its clear plastic loop.

Traduci

Passo 8 Upper Case

iBook G3 Clamshell Modem Replacement, Upper Case: passo 8, immagine 1 di 1

Use a straightened paperclip to manually eject the CD-ROM tray.

Traduci

Passo 9

Turn the computer over so that the bottom is facing up.
Remove the following Torx screws:
Four short T8 Torx near the battery compartment.
Two long T8 Torx near the hinges.

Traduci

Passo 10

Pull the CD-ROM drive tray partly out.
Remove the silver Phillips screw from the plastic casing.

Traduci

Note to people whose Clamshell ibook doesn't have the CD tray cover any more -- you do not have to open the drive for this part because when you flip the machine to remove the screw, it will be visible. The cover normally obscures this part.

Marissa Stardance - 10 ott 2023 Replica

Passo 11

Turn the computer over.
Remove the three Phillips screws.

Traduci

Please note: these screws can (and may!) strip easily, so take extra care in removing them!

LambdaCalculus - 3 giu 2009 Replica

Passo 12

This is a diagram of the trackpad ribbon clamp connector you will disconnect in the next step.
1) With your fingernails, grasp the locking bar on either side and pull up a small amount (about 1/16" or 2 mm).
2) After disengaging the locking bar, slide the cable out of the connector.

Traduci

In part 1, you can use a small flat-blade screwdriver to lift the locking bar. This will not put pressure on the cable itself. Each end of the locking bar will click when it has been lifted sufficiently.

Don Solomon - 25 giu 2011 Replica

Passo 13

Loosen the trackpad clamp by pulling the top piece up slightly, freeing the trackpad ribbon.
Slide the orange trackpad ribbon out of the clamp.

Traduci

Before going to the next step, remove 4 T8 screws from bottom of case.

gestler - 16 lug 2020 Replica

Passo 14

Do not lift the upper case too far without first disconnecting the audio cable.
Push out the rim of the lower case and pull up on the upper case, grasping it just to the left of the optical drive.
Repeat the above step on the upper left corner of the upper case, grasping the bottom left corner of the upper case.

Traduci

Passo 15

Disconnect the audio cable.

Traduci

Passo 16

Grasp the upper case on either side of the keyboard space and rotate up and away from the screen.
You may be thinking you're about to break your upper case. Not to worry - the tabs holding the upper and lower cases together are very strong. Simply apply even pressure and continue to rotate the upper case up and away from the screen until it comes free.

Traduci

When replacing the upper case, test the trackpad button to make sure it clicks before proceeding. If it does not operate properly, remove the upper case and reattach it.

Don Solomon - 26 giu 2011 Replica

Once you free the back half, pull the the case forward, not up so much, or you’ll break the tabs on the sides by the optical drive on the right, and about the same place on the left.

Rick - 2 mag 2019 Replica

I second this.

DistroHopper39B - 1 ago 2020

Passo 17 Modem

iBook G3 Clamshell Modem Replacement, Modem: passo 17, immagine 1 di 1

Remove the following Phillips screws:
Remove the longer Phillips screw from the middle-rear of the modem shield.
Remove the three identical Phillips screws, two on either side of the EMI fingers, and the remaining one on the right side of the modem shield.
Remove the larger Phillips screw that secures the EMI fingers to the modem board.
Remove the EMI fingers.