/
Il mio banco da lavoro

Ottieni un rapido accesso alle guide, ai componenti e alle risposte per i tuoi dispositivi

DE
Deutsch
ES
Español
IT
Italiano
PT
Português
TR
Türkçe
JP
日本語
EN
English
FR
Français
NL
Nederlands
RU
Pусский
ZH
中文
KO
한국어
Unisciti
Accedi
Unisciti alla più grande community di riparazione al mondo
VTech InnoTab 2s Speaker Replacement

VTech InnoTab 2s Speaker Replacement

Esthevan Romeiro

Esthevan Romeiro e 2 altri collaboratori

Ultimo aggiornamento il February 17, 2024

15 - 30 minuti
Moderato

Introduzione

Vai al passo 1

You no longer get sound from the speakers on your tablet. This guide will help you gain access to the speaker on your tablet for removal or replacement.

Cosa ti serve

Strumenti

Mostra di più…

  1. VTech InnoTab 2s Speaker Replacement, Back Panel: passo 1, immagine 1 di 1

    • Turn your device to where the back panel is facing you.

    Traduci

  2. VTech InnoTab 2s Speaker Replacement: passo 2, immagine 1 di 2 VTech InnoTab 2s Speaker Replacement: passo 2, immagine 2 di 2

    • Lift the Leg all the way up and twist the bottom to remove.

    • Once the bottom part pops out the whole leg should just come off.

    • Remove any game cartridge from the device.

    Traduci

  3. VTech InnoTab 2s Speaker Replacement: passo 3, immagine 1 di 3 VTech InnoTab 2s Speaker Replacement: passo 3, immagine 2 di 3 VTech InnoTab 2s Speaker Replacement: passo 3, immagine 3 di 3

    • Remove all of the plastic tabs on the device. These are covering screws that will need to be removed.

    • These covers are made of hard plastic so they may be difficult to remove.

    • There is a special tab in the cartridge cover that is made of rubber, make sure to not break this tab.

    Traduci

  4. VTech InnoTab 2s Speaker Replacement: passo 4, immagine 1 di 2 VTech InnoTab 2s Speaker Replacement: passo 4, immagine 2 di 2

    • Remove all nine screws from the back of the device using a J0 bit.

    • Remove the small battery.

    Traduci

  5. VTech InnoTab 2s Speaker Replacement: passo 5, immagine 1 di 2 VTech InnoTab 2s Speaker Replacement: passo 5, immagine 2 di 2

    • Using a plastic opening tool, detach the backplate from the front piece.

    • Do not use excessive force. Double check that you removed all the screws if the panel is not coming off easily.

    • Once the backplate has been removed, you will have access to the circuit board.

    Traduci

  7. VTech InnoTab 2s Speaker Replacement, Motherboard: passo 6, immagine 1 di 1

    • First begin by removing the three cross-head screws using a J0 bit.

    Traduci

  8. VTech InnoTab 2s Speaker Replacement: passo 7, immagine 1 di 1

    • First remove the ribbon cables. There are two highlighted by the red squares

    • Do not apply too much pressure and make sure that the black plastic tabs are fully open before you pull the cable out.

    Traduci

  9. VTech InnoTab 2s Speaker Replacement: passo 8, immagine 1 di 1

    • Remove the camera from the assembly and put is a safe place so that it will not get damaged.

    Traduci

  10. VTech InnoTab 2s Speaker Replacement: passo 9, immagine 1 di 1

    • Remove the board from the main assembly.

    • Be careful not to pull too hard so that the cables aren't broken.

    Traduci

  11. VTech InnoTab 2s Speaker Replacement: passo 10, immagine 1 di 1

    • De-solder the points shown to fully remove the cables and free the board.

    • A soldering guide offered by IFIXIT can be found here Soldering Skills.

    Traduci

  12. VTech InnoTab 2s Speaker Replacement, Speaker: passo 11, immagine 1 di 1

    • Desolder these two points from the circuit board.

    • A soldering guide provided by iFixit can be found here: Soldering Skills.

    Traduci

  13. VTech InnoTab 2s Speaker Replacement: passo 12, immagine 1 di 1

    • Remove the two screws that are holding down the speaker.

    Traduci

  14. VTech InnoTab 2s Speaker Replacement: passo 13, immagine 1 di 1

    • Desolder the two wires that are connected to the speaker.

    • A soldering guide offered by IFIXIT can be found here: Soldering Skills.

    Traduci
Conclusione

To reassemble your device, follow these instructions in reverse order.

Autore

con 2 altri collaboratori

Esthevan Romeiro

Membro da: 10/06/16

261 Reputazione

4 Guide realizzate

Distintivi: 9

+6 altri distintivi

Team

USF Tampa, Team 5-1, Lacy Fall 2016 Membro di USF Tampa, Team 5-1, Lacy Fall 2016

USFT-LACY-F16S5G1

4 Membri

12 Guide realizzate

1Commento della guida

Thank you for this guide. I have a Vtech (ELC) toy flip phone, which has similar issue. I think your guide is incomplete, has only 13 steps and stops at desoldering the speaker. What speaker shall I get, does it matter, or just the size matters? Thank you!

Scream - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 1

Ultimi 7 Giorni: 1

Ultimi 30 Giorni: 18

Tutti i Tempi: 316