/
Il mio banco da lavoro

Ottieni un rapido accesso alle guide, ai componenti e alle risposte per i tuoi dispositivi

DE
Deutsch
ES
Español
IT
Italiano
PT
Português
TR
Türkçe
JP
日本語
EN
English
FR
Français
NL
Nederlands
RU
Pусский
ZH
中文
KO
한국어
Unisciti
Accedi
Unisciti alla più grande community di riparazione al mondo
Ricambi
GuideRisposte
Modifica
Motorola RIZR Z3 LCD Replacement

Motorola RIZR Z3 LCD Replacement

Brooke Shuford

Brooke Shuford e 5 altri collaboratori

Ultimo aggiornamento il January 28, 2014

30 minuti
Moderato

Introduzione

Vai al passo 1

Guide to replacing a broken LCD.

Cosa ti serve

Strumenti

  • iFixit Opening Tool
    iFixit Opening Tool
  • Spudger
    Spudger
  • T4 Torx Screwdriver
    T4 Torx Screwdriver

Mostra di più…

  1. Motorola RIZR Z3 LCD Replacement, Battery: passo 1, immagine 1 di 2 Motorola RIZR Z3 LCD Replacement, Battery: passo 1, immagine 2 di 2

    • Press the panel release button on the top of the phone and simultaneously pull the rear panel away from the phone.

    Modifica

  2. Motorola RIZR Z3 LCD Replacement: passo 2, immagine 1 di 2 Motorola RIZR Z3 LCD Replacement: passo 2, immagine 2 di 2

    • Tilt the battery by lifting at the exposed notch.

    • Slide the battery out of its casing.

    Modifica

  3. Motorola RIZR Z3 LCD Replacement, Motherboard: passo 3, immagine 1 di 1

    • Use a T4 screwdriver to unscrew all six of the .216 inch screws that attach the housing to the case.

    Modifica

  4. Motorola RIZR Z3 LCD Replacement: passo 4, immagine 1 di 2 Motorola RIZR Z3 LCD Replacement: passo 4, immagine 2 di 2

    • Use a plastic opening tool to lift the plastic casing.

    • Pull the plastic casing directly away from the phone.

    Modifica

  5. Motorola RIZR Z3 LCD Replacement: passo 5, immagine 1 di 1

    • Lift the black rubber loudspeaker housing up and out of the plastic casing.

    Modifica

  7. Motorola RIZR Z3 LCD Replacement: passo 6, immagine 1 di 2 Motorola RIZR Z3 LCD Replacement: passo 6, immagine 2 di 2

    • Use a plastic opening tool to gently lift up the SIM card reader, located above the rubber antenna casing. You should hear a click as it releases.

    • Caution: Remove carefully, if broken, the phone will not be able to make calls.

    Modifica

  8. Motorola RIZR Z3 LCD Replacement: passo 7, immagine 1 di 2 Motorola RIZR Z3 LCD Replacement: passo 7, immagine 2 di 2

    • Use a plastic opening tool to pry the two ribbon cable connectors, unclipping them from their sockets on the motherboard.

    • Caution: Remove carefully, if broken, the phone will not function properly.

    Modifica

  9. Motorola RIZR Z3 LCD Replacement: passo 8, immagine 1 di 2 Motorola RIZR Z3 LCD Replacement: passo 8, immagine 2 di 2

    • Use a plastic opening tool to gently pry the motherboard up until you can tilt it with your fingers. Unhook it from the casing and slowly pull it out.

    • Caution: Do this gently Unclipping too fast may cause damage to your phone.

    Modifica

  10. Motorola RIZR Z3 LCD Replacement, LCD: passo 9, immagine 1 di 1

    • Turn the phone to the front.

    • Push the keypad out through the plastic casing.

    Modifica

  11. Motorola RIZR Z3 LCD Replacement: passo 10, immagine 1 di 1

    • Turn the phone to the side.

    • Thread the hinges of the slider through their holes in the casing and pull the slider down and away from the casing.

    Modifica

  12. Motorola RIZR Z3 LCD Replacement: passo 11, immagine 1 di 1

    • Use a T4 screwdriver to unscrew the two .15 inch screws holding the LCD to the faceplate.

    Modifica

  13. Motorola RIZR Z3 LCD Replacement: passo 12, immagine 1 di 3 Motorola RIZR Z3 LCD Replacement: passo 12, immagine 2 di 3 Motorola RIZR Z3 LCD Replacement: passo 12, immagine 3 di 3

    • Use a spudger to pry the plastic screen casing partially up from the LCD unit.

    • Use the spudger to pry the ribbon cable away from its clip on the LCD unit.

    • Caution: Do this carefully, damage to this ribbon cable will cause a blank screen.

    • Pull the plastic screen casing directly away from the LCD unit.

    Modifica

  14. Motorola RIZR Z3 LCD Replacement: passo 13, immagine 1 di 2 Motorola RIZR Z3 LCD Replacement: passo 13, immagine 2 di 2

    • Use a spudger to lift the LCD partially away from the metal casing.

    • Use the spudger to pry the ribbon cable directly up from its clip on the metal casing.

    • Caution: Damage to the ribbon cable here will cause screen damage.

    • Pull the LCD completely away from the metal casing.

    Modifica
Conclusione

To reassemble your device, follow these instructions in reverse order.

Autore

con 5 altri collaboratori

Brooke Shuford

Membro da: 10/10/11

65 Reputazione

3 Guide realizzate

Distintivi: 7

+4 altri distintivi

Team

Cal Poly, Team 5-34, Amido Fall 2011 Membro di Cal Poly, Team 5-34, Amido Fall 2011

CPSU-AMIDO-F11S5G34

4 Membri

6 Guide realizzate

0Commenti sulla guida

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 0

Ultimi 30 Giorni: 18

Tutti i Tempi: 1,011