Introduzione

Use this guide to replace a cracked or faulty screen, including the display and digitizer, on your Google Pixel 2. There may also be small parts that need to be transferred from the original display to the replacement. Inspect both displays closely to make sure all relevant components are moved from the original display to the replacement.

If your display glass is cracked, keep further breakage contained and prevent bodily harm during your repair by taping the glass. This also makes a smooth surface allowing the suction cup to bond.
  • If your display glass is cracked, keep further breakage contained and prevent bodily harm during your repair by taping the glass. This also makes a smooth surface allowing the suction cup to bond.

  • Apply a suction cup as close to the volume button edge of the phone as you can while avoiding the curved edge.

    • The suction cup will not make a good seal on the curved portion of the glass.

That isn’t the SIM slot edge, that’s the volume control. Is the description or the photo incorrect?

Gregory Cavallaro - Replica

Pull up on the suction cup with firm, constant pressure and insert an opening pick between the front panel and rear case.
  • Pull up on the suction cup with firm, constant pressure and insert an opening pick between the front panel and rear case.

  • This requires a significant amount of force and patience. If you have trouble, rock the suction cup and screen to weaken the adhesive, or apply heat with an iOpener, heat gun, or hair dryer.

Aggiungi Commento

  • In the following steps, extra caution is required in certain areas to avoid damage to the phone:

    • Do not insert the pick more than 0.5 inches into the bottom edge of the phone. If the pick contacts the folded portion of the OLED panel it can damage the display.

    • Only make very shallow cuts in the upper left corner, prying deeply can damage the front-facing camera.

Aggiungi Commento

  • In the following steps, use the flat of the opening pick, rather than a corner, to cut here. This will help prevent inserting the pick too deeply.

  • Slide the opening pick up the right side of the phone to separate the display adhesive.

Aggiungi Commento

  • Slide the opening pick around the upper-right corner and along the top edge of the phone.

Aggiungi Commento

  • Slide the pick around the upper-left corner of the phone and down the left edge of the phone.

Aggiungi Commento

  • Slide the pick around the bottom-left corner and along the bottom of the phone.

Aggiungi Commento

  • Reinsert the pick at the top edge of the phone and gently pry up the display.

    • If the display doesn't readily lift, do some extra prying to separate the last of the adhesive. The adhesive near the upper speaker is thicker than other places.

  • Don't try to fully separate the display yet, as a fragile ribbon cable still connects it to the phone's motherboard.

Aggiungi Commento

  • Carefully lay the display down on top of the rear case as shown, making sure not to crease or tear the display ribbon cable.

  • Remove the two 4.0 mm T5 Torx screws securing the display cable bracket.

Aggiungi Commento

  • Remove the display cable bracket.

Aggiungi Commento

  • Use the point of a spudger to lift the display cable connector up and out of its socket on the motherboard.

  • To re-attach press connectors like this one, carefully align and press down on one side until it clicks into place, then repeat on the other side. Do not press down on the middle. If the connector is misaligned, the pins can bend, causing permanent damage.

  • If any part of your screen doesn't respond to touch after your repair re-seat this connector, making sure it clicks fully into place and that there's no dust or other obstruction in the socket.

Aggiungi Commento

  • Before installing a new display, it's very important to remove all traces of the old adhesive from the frame, while taking special care to remove any small glass fragments.

  • After removing all traces of glue and glass from the frame, clean the adhesion areas with high concentration isopropyl alcohol (at least 90%), then apply the new adhesive.

  • The best way to secure the new screen is with a sheet of custom-cut double-sided tape, but high-adhesion double-sided tape, like Tesa 61395, will work too. Apply the tape to the edges of the frame where the old adhesive was, align the screen, and press it into place.

Be careful not to get rubbing alcohol on the grey rubbery backing (has “X”s stamped in it.) It will disintegrate it!

Brian Conner - Replica

What width tape would be needed for this?

Christopher Long - Replica

I’d recommend 1 mm tape for this repair, and most other display repairs. Wider tape usually won’t fit on the edges of the display.

Adam O'Camb -

Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 6 persone hanno completato questa guida.

Adam O'Camb

Membro da: 11/04/2015

32.357 Reputazione

103 Guide realizzate

Team

iFixit Membro di iFixit

Community

107 Membri

6.510 Guide realizzate

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 50

Ultimi 7 Giorni: 405

Ultimi 30 Giorni: 1,739

Tutti i Tempi: 8,758