Salta al contenuto principale
Unisciti alla Community delle riparazioni - Crea un account
Sanyo VPC S1275 LCD Screen Replacement

Sanyo VPC S1275 LCD Screen Replacement

Evan Perez

Evan Perez e 6 altri collaboratori

Ultimo aggiornamento il 27 nov 2020

15 - 20 minuti
Moderato

Introduzione

Vai al passo 1

Use this guide to gain entry to LCD screen and replace it if necessary.

Cosa ti serve

Strumenti

  • Phillips #00 Screwdriver
    Phillips #00 Screwdriver
  • Spudger
    Spudger
  1. Sanyo VPC S1275 LCD Screen Replacement, Battery: passo 1, immagine 1 di 1
    • Place your thumb on the right side of the camera over the battery door.

    • Slide the battery door to the right until the door lifts up.

  2. Sanyo VPC S1275 LCD Screen Replacement: passo 2, immagine 1 di 1
    • Remove and recycle old batteries.

  3. Sanyo VPC S1275 LCD Screen Replacement, Case: passo 3, immagine 1 di 3 Sanyo VPC S1275 LCD Screen Replacement, Case: passo 3, immagine 2 di 3 Sanyo VPC S1275 LCD Screen Replacement, Case: passo 3, immagine 3 di 3
    • Remove the following six screws using the Phillips #00 screwdriver:

    • Two screws on the left side of the camera.

    • Two screws on the right side of the camera.

    • Two screws on the bottom of the camera.

  4. Sanyo VPC S1275 LCD Screen Replacement: passo 4, immagine 1 di 2 Sanyo VPC S1275 LCD Screen Replacement: passo 4, immagine 2 di 2
    • Open the battery slot on the bottom of the camera by sliding the door to the right.

    • Remove the single 4 mm screw on the bottom right using the Phillips #00 screwdriver.

  5. Sanyo VPC S1275 LCD Screen Replacement: passo 5, immagine 1 di 3 Sanyo VPC S1275 LCD Screen Replacement: passo 5, immagine 2 di 3 Sanyo VPC S1275 LCD Screen Replacement: passo 5, immagine 3 di 3
    • Insert a spudger in the seam at the bottom of the camera.

    • Gently separate the rear case from the front of the camera.

  6. Sanyo VPC S1275 LCD Screen Replacement: passo 6, immagine 1 di 1
    • This step is only needed for the case and logic board replacement

    • Using the Phillips #00 screwdriver, remove the single screw attached to the front casing in the top left corner. The front case should easily separate.

  7. Sanyo VPC S1275 LCD Screen Replacement: passo 7, immagine 1 di 1
    • This step is only needed for the case replacement.

    • Using the Phillips #00 screwdriver, remove the screw on the inside of the battery door.

    • Slide the battery door off of the hinge.

  8. Sanyo VPC S1275 LCD Screen Replacement, LCD Screen: passo 8, immagine 1 di 2 Sanyo VPC S1275 LCD Screen Replacement, LCD Screen: passo 8, immagine 2 di 2
    • Using the spudger, carefully lift up the LCD screen, making sure to keep the ribbon cable intact.

    • Place the LCD screen on a non-abrasive surface.

  9. Sanyo VPC S1275 LCD Screen Replacement: passo 9, immagine 1 di 1
    • Using the spudger lift the black flap up to release the ribbon cable.

    • The LCD screen will now be completely detached from the camera.

Conclusione

To reassemble your device, follow these instructions in reverse order.

Preparati per le riparazioni future

Acquista tutti

Evan Perez

Membro da: 04/15/10

19 Reputazione

2 Guide realizzate

Team

Cal Poly, Team 24-24, Regan Spring 2010 Membro di Cal Poly, Team 24-24, Regan Spring 2010

CPSU-REGAN-S10S24G24

4 Membri

12 Guide realizzate

0Commenti sulla guida

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 1

Ultimi 30 Giorni: 17

Tutti i Tempi: 3,212