Introduzione

This repair guide will give instructions on how to remove the Macintosh PowerBook 1400c RAM.

Parti

Nessuna parte richiesta.

Turn the device upside down and then locate the battery latch near the front of the device.
  • Turn the device upside down and then locate the battery latch near the front of the device.

Aggiungi Commento

Slide the latch to the left to release the battery.
  • Slide the latch to the left to release the battery.

Aggiungi Commento

  • Continue holding the latch then gently pull the battery out of the device.

  • Place the battery in a safe location.

Aggiungi Commento

  • Locate the CD-ROM Drive latch.

Aggiungi Commento

  • Slide the latch to the right to release the CD ROM drive.

Aggiungi Commento

  • Continue holding the latch then gently pull the CD-ROM Drive out of the device.

  • Place the CD ROM drive in a safe location.

Aggiungi Commento

  • Locate the speaker cover.

Aggiungi Commento

  • Press firmly on each end of the speaker cover and slide it to the left.

I found it was easy to get a spudger over the left edge and lift it up a bit, then push the bar to the left, It pops right off after that.

Jimmy James - Replica

  • Gently lift the speaker cover to remove it.

Aggiungi Commento

  • Lift the keyboard up from the back using a spudger(wedge side).

Aggiungi Commento

  • Gently lift the keyboard until only the ribbon cable remains attached.

Aggiungi Commento

  • Tilt the keyboard away from the screen.

Aggiungi Commento

  • Locate the six screws that secure the heatsink.

This is not necessary to remove the HDD. Go directly to step 20.

Kenneth DeVries - Replica

That isn't the HDD!

Dix Dox - Replica

  • Remove the six screws from the heatsink using the Philips #1 screwdriver.

Aggiungi Commento

  • Lift the heatsink from the side closest to the laptop screen.

Aggiungi Commento

  • Remove the heatsink.

Aggiungi Commento

  • Gently pull up on the beige ribbon lock until it moves a short distance on both sides to separate the ribbon cable from the connector.

Aggiungi Commento

  • Detach the ribbon cable.

Aggiungi Commento

  • Remove the keyboard.

Aggiungi Commento

  • Identify RAM Memory stick

  • These are the upgradeable RAM Memory sticks, they must be removed first

Aggiungi Commento

  • Gently grasp the ram on the far end as shown in the picture and then pull up and away from the right side of the computer

Aggiungi Commento

  • Remove the upgradeable RAM stick

  • If the upgradeable RAM stick is all you are repairing you can end the guide here, however to remove the factory installed RAM please continue

Aggiungi Commento

  • Gently grasp the factory installed RAM by grabbing each end as shown in the picture and pull the stick directly up

Aggiungi Commento

  • Remove the factory installed RAM memory module

Aggiungi Commento

Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 4 persone hanno completato questa guida.

Kian Dinyari

Membro da: 07/04/2011

125 Reputazione

1 Guida realizzata

Team

Cal Poly, Team 10-39, Forte Spring 2011 Membro di Cal Poly, Team 10-39, Forte Spring 2011

CPSU-FORTE-S11S10G39

5 Membri

6 Guide realizzate

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 3

Ultimi 30 Giorni: 22

Tutti i Tempi: 2,854