Introduzione

The flash unit provides necessary lighting when not enough is available.

Parti

Nessuna parte richiesta.

Slide grey latch to open the battery compartment.
  • Slide grey latch to open the battery compartment.

Aggiungi Commento

Push orange retaining clip to the right to free battery.
  • Push orange retaining clip to the right to free battery.

Aggiungi Commento

  • Remove battery from the camera.

Aggiungi Commento

  • Remove the lanyard.

Aggiungi Commento

  • Remove the two 2.3mm screws (underneath the name plate) and two 2.8mm screws (next to the threaded tripod mount) from the bottom face of the camera.

  • Be careful to keep track of the different screw sizes as you proceed with this guide.

Aggiungi Commento

  • Remove the single 3.8mm screw from the back face of the camera.

Aggiungi Commento

  • Remove the two 2.3mm screws from the right face of the camera.

Aggiungi Commento

  • Remove the two 3.2mm screws (outside edge) and two 3.7mm screws (towards middle) from the left side of the camera body.

Aggiungi Commento

  • Pull the back face panel away from the front end of the body. This may take some wiggling and force.

Aggiungi Commento

  • Remove the CF card door from the left side of the camera body.

Aggiungi Commento

  • Remove the rubber digital a/v out cap by sliding it out of the groove on the front plate.

Aggiungi Commento

  • Remove the front face by sliding it off.

Aggiungi Commento

  • Remove the rubber seal that goes over the right side of the viewfinder.

Aggiungi Commento

  • Remove the two 3.9mm screws that retain the laminated cooper sheet.

Aggiungi Commento

  • Remove the seven wire connections that connect to the motherboard.

Aggiungi Commento

  • Remove the single 3.8mm screw that is on the motherboard.

Aggiungi Commento

  • Carefully remove the motherboard from the main frame of the camera body.

Aggiungi Commento

  • After completing the removal of the motherboard, remove the tripod mounting screws (3.4mm) on the left side

Aggiungi Commento

  • Carefully pry the left side of the housing plate from the bottom of the tripod mounting plate, releasing it from the two alignment pegs next to the screws

Aggiungi Commento

  • Lift the left side of the tripod mounting plate towards you, lift free the mounting plate from the rest of the assembly

  • Be careful because there are still wire connections attached to the mounting plate which you don't want to remove

Aggiungi Commento

  • Remove the 2.1mm screws from the bottom and top of the screen connecting it to the housing plate

Aggiungi Commento

  • Unsolder the four points at the top of the screen with a soldering iron

Aggiungi Commento

  • You do not need to unsolder the screen to get to the lens, but follow the rest of the steps to free the screen from the housing plate.

Aggiungi Commento

  • Remove the card-reader shield by removing the screw at the top of the shield.

Aggiungi Commento

  • Remove the 2 black screws that attach the battery box to the housing plate.

  • The second picture shows the battery box detached from the housing plate.

Aggiungi Commento

  • Remove the three (3.1mm) black screws that were behind the screen and battery box.

Aggiungi Commento

  • Carefully remove the lens.

  • Remove the bottom side of the lens first before the viewfinder side.

  • Be careful of wires and delicate parts.

Aggiungi Commento

  • Remove the 3.3 mm screw from underneath the clear plastic flash unit on the front side.

Aggiungi Commento

  • Remove the 3.4mm screw from the top of the flash unit and housing plate.

Aggiungi Commento

  • Remove the 2.1mm screw from the interlocking clip on the right.

Aggiungi Commento

  • Pull the flash unit away from the interlocking clip on the housing plate.

  • This will require some maneuvering to free the interlocking clip from the housing plate.

Aggiungi Commento

  • Slide the flash unit to the left and away from the housing plate.

Aggiungi Commento

  • Unsolder the pink wire from the condenser.

Aggiungi Commento

  • Remove the clear plastic cover from the white wire by lifting off with finger.

  • Desolder the white wire.

Aggiungi Commento

  • Remove the gray wire by desoldering it from the underside of the flash unit.

Aggiungi Commento

  • Carefully pull the flash unit off the condenser. There is tape underneath, so some force may be required.

Aggiungi Commento

Conclusione

To reassemble your device, follow these instructions in reverse order.

Tanya

Membro da: 20/04/2011

111 Reputazione

1 Guida realizzata

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 0

Ultimi 30 Giorni: 0

Tutti i Tempi: 612