Salta al contenuto principale

Aggiusta la tua roba

Diritto alla Riparazione

Store

Introduzione

Use this guide to remove the rear glass of the Samsung Galaxy S9.

Opening the Samsung Galaxy S9 will damage the waterproof sealing on the device. If you do not replace the adhesive seals, your phone will function normally, but will loose its water-protection.

You’ll need replacement adhesive to reattach components when reassembling the device.

  1. Before you begin, switch off your phone.
    • Before you begin, switch off your phone.

    • Apply a heated iOpener to a long edge of the phone to loosen the adhesive beneath the rear glass. Apply the iOpener for at least two minutes.

    • You might need to reheat and reapply the iOpener several times during the removal procedure to get the adhesive warm enough to cut. Follow the iOpener instructions to avoid overheating.

    • The adhesive of the Samsung Galaxy S9 is very strong. A hair dryer, heat gun, or hot plate may also be used if you aren't able to open the device with the iOpener. Be careful not to overheat the phone—the AMOLED display and internal battery are both susceptible to heat damage.

  2. In the following steps, you'll be cutting through the adhesive securing the back cover.
    • In the following steps, you'll be cutting through the adhesive securing the back cover.

    • The adhesive in the inside of the back cover is laid out as seen in the image.

    • You'll be slicing through the adhesive in the areas shown:

    • Thick portions of adhesive

    • Thin areas of adhesive

    • Avoid prying or slicing in this area, to protect the fingerprint sensor flex cable.

  3. If the phone's rear glass is cracked, the suction cup may not stick. Try lifting it with strong tape, or superglue the suction cup in place and allow it to cure so you can proceed. Press a suction cup onto the back cover. Lift the back cover's bottom edge with your suction cup, opening a slight gap between the back cover and the frame.
    • If the phone's rear glass is cracked, the suction cup may not stick. Try lifting it with strong tape, or superglue the suction cup in place and allow it to cure so you can proceed.

    • Press a suction cup onto the back cover.

    • Lift the back cover's bottom edge with your suction cup, opening a slight gap between the back cover and the frame.

    • This may require a significant amount of force, but you only need to open a very slight gap with the suction cup to insert your tool. If you have trouble, apply more heat to further soften the adhesive, and try again. The adhesive cools very fast, so you may need to heat it repeatedly.

    • Insert an opening pick in the gap you created and slide it to the bottom right corner.

    • Insert a second opening pick and slide it to the bottom left corner.

    • Insert a third opening pick to prevent the adhesive from resealing during the rest of the removal procedure.

  4. SKIP THE UPGRADE

    Save by fixing with an all-in-one kit.

    Shop iPhone Fix Kits

    SKIP THE UPGRADE

    Save by fixing with an all-in-one kit.

    Shop iPhone Fix Kits
  5. While inserting only the tip of the opening pick, slide it from the bottom left corner along the side to the top. Slide the pick around the top corner and leave it there to prevent the adhesive from resealing.
    • While inserting only the tip of the opening pick, slide it from the bottom left corner along the side to the top.

    • Slide the pick around the top corner and leave it there to prevent the adhesive from resealing.

  6. Slide the opening pick from the bottom right corner along the side to the top. Apply more heat if the adhesive becomes hard to cut. During the removal process, the back cover is under tension all the time and is likely to break if the adhesive isn't softened enough. Slide the opening pick around the corner and cut the remaining adhesive at the top of the phone.
    • Slide the opening pick from the bottom right corner along the side to the top.

    • Apply more heat if the adhesive becomes hard to cut. During the removal process, the back cover is under tension all the time and is likely to break if the adhesive isn't softened enough.

    • Slide the opening pick around the corner and cut the remaining adhesive at the top of the phone.

    • Don't open the phone all the way yet. The fragile fingerprint sensor cable still connects the back cover to the motherboard.

  7. Carefully lift the side of the rear glass where the volume button is located. Use the edge of a spudger to pry up and disconnect the fingerprint sensor flex cable.
    • Carefully lift the side of the rear glass where the volume button is located.

    • Use the edge of a spudger to pry up and disconnect the fingerprint sensor flex cable.

  8. Remove the rear glass.
    • Remove the rear glass.

    • When reassembling follow this guide to replace the adhesive and reinstall the rear glass.

    • In case you want to replace your rear glass follow this guide to transfer the rear camera bezel including the fingerprint.

Conclusione

Secure the new back cover with pre-cut adhesive or double-sided adhesive tape.

To reassemble your device, follow these instructions in reverse order.

After installing the rear cover, apply strong, steady pressure to your phone for several minutes to help the adhesive form a good bond, such as by placing it under a stack of heavy books.

Altre 5 persone hanno completato questa guida.

Dominik Schnabelrauch

Membro da: 23/11/2016

71.593 Reputazione

320 Guide realizzate

Team

iFixit Membro di iFixit

Community

128 Membri

13.120 Guide realizzate

Sollte nach Abschluss der Reparatur der Fingerabdrucksensor nicht funktionieren bitte folgende Schritte machen:

1. Schalte das Handy aus und hänge es ein Ladegerät

2. Starte das Handy im Restore Modus indem du die Bixby, Lauter und Powertaste gleichzeitig drückst bis das Samsung Logo kommt.

3. Wähle in dem Menü den Punkt: Wipe Cache Partition aus und bestätige mit Power deine Auswahl.

4. Starte das Gerät neu.

Sebastian Coenen - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 12

Ultimi 7 Giorni: 74

Ultimi 30 Giorni: 330

Tutti i Tempi: 5,259