Questa versione può contenere modifiche errate. Passa all'ultima istantanea verificata.
Cosa ti serve
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Insert a paperclip or SIM card eject tool into the small hole in the SIM card tray on the upper right edge of the phone.
-
Press the tool into the hole to eject the tray.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
If possible, drain the battery before disassembly. When the battery is charged, there's an increased risk of a dangerous thermal event if the battery is overheated or damaged during repairs.
-
Prepare an iOpener and heat the back of the phone along its bottom edge for about two minutes, or until it's slightly too hot to touch. This will help soften the adhesive securing the rear glass.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Apply a suction cup to the bottom edge of the rear glass.
-
Pull up on the suction cup with firm, constant pressure to create a slight gap between the rear glass and the frame.
-
If you have trouble, apply more heat to further soften the adhesive, and try again. The adhesive cools quickly, so you may need to heat it repeatedly.
-
Insert an opening pick into the gap you created under the rear glass.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Slide the pick all along the bottom edge of the phone to slice through the adhesive securing the rear glass.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Heat the right edge of the back of the phone to soften the adhesive underneath.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Slide the pick along the right edge of the rear glass to separate the adhesive underneath.
-
Leave the pick under the top right corner of the glass to prevent the adhesive from re-adhering. Continue with a new pick.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Heat the top edge of the back of the phone to soften the rear glass adhesive.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Slide the pick all along the top edge of the phone to slice through the adhesive securing the rear glass.
-
Leave the pick under the top left corner of the glass to prevent the adhesive from re-adhering. Continue with a new pick.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Heat the left edge of the back of the phone to soften the adhesive underneath.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Slide a pick along the left edge of the phone to slice through the rear glass adhesive.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
There are two strips of adhesive on either side of the lower half of the phone that must be separated to remove the rear glass panel.
-
You will need to release these adhesive strips without damaging the fingerprint sensor cable located in the center of the phone.
-
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Insert the flat end of a spudger into the lower half of the right side of the phone about 2 cm and slide it down the right edge to release the right strip of adhesive.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Insert a spudger into the lower half of the left side of the phone about 2 cm and slide it down the left edge to release the left strip of adhesive.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
Attrezzo utilizzato in questo passaggio:Tesa 61395 Tape$5.99-
If the glass remains stuck, re-heat and slice any remaining adhesive repeatedly as needed.
-
Lift the rear glass carefully, making sure it's fully separated from any adhesive.
-
Open the rear glass.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a Phillips screwdriver to remove the two screws securing the fingerprint sensor cable retention bracket:
-
One silver 1.5 mm screw
-
One gold 3.5 mm screw
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a pair of tweezers to remove the fingerprint sensor cable retention bracket.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the pointed edge of a spudger to disconnect the fingerprint sensor cable.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a Phillips screwdriver to remove the fifteen gold 3.5 mm screws securing the plastic midframe.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Insert a spudger into the notch on the upper right edge of the midframe.
-
Pry the midframe up to release the clips securing it to the device's aluminum frame.
-
Remove the plastic midframe.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a spudger to pry up and disconnect the battery cable.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a pair of tweezers to carefully remove the tape covering the camera module connector.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the flat end of a spudger to pry up the camera module connector and disconnect it.
-
Remove the camera module.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Insert the pointed end of a spudger underneath the bottom left corner of the earpiece speaker and pry it up.
-
Remove the earpiece speaker.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a spudger to pry up and disconnect the daughterboard flex cable from the motherboard.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a spudger to pry up and disconnect the display flex cable.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a pair of tweezers to remove the piece of tape covering the side button flex cable connector.
-
Retain this piece of tape for reassembly.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the pointed end of a spudger to flip up the locking flap on the side button ZIF connector.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a pair of tweezers to slide the side button cable out of its socket.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the pointed end of a spudger to pry up and disconnect the black antenna cable.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the pointed end of a spudger to pry up and disconnect the blue antenna cable.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a Phillips screwdriver to remove the two silver 2 mm screws securing the motherboard.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the pointed edge of a spudger to pry up the top right corner of the motherboard.
-
Remove the motherboard.
-
Annulla: non ho completato questa guida.
Altre 3 persone hanno completato questa guida.
2 Commenti
Hi guys my problem with my Motorola g6 play is display light it is verry low I tried to sett it but still no light.