Questo utente non ha ancora compilato il proprio profilo.
Domande
I've managed to pull the pad twice on the far left GND pad and the 2 circles below it. Is there and location I can jump...
Per saperne di piùI have only the board from a a1286 i7 macbook pro the problem is I only have a dc magsafe jack for the a1181 older macbook...
Per saperne di piùA1260 Have a macbook pro showing typical signs of no video upon inspecting the GPU the copper block on the top of the chip...
Per saperne di piùI was wondering how much difference a set of off knock LCR smart Tweezers match up to the real ones I see them on amazon...
Per saperne di piùMacbook Pro A1226 2.2 Ghz I have a a1226 2.2 santa rosa MBP. I have a Intel Laptop CPU T7700 2.4ghz 800mhz FSB from a pull...
Per saperne di piùOn this macbook pro a1226 i'm trying to diagnose, there is a red line sometimes black down about the middle of the screen...
Per saperne di piùI got this phone from a friend that quit turning on. I brought it home conntected to itunes nothing , then a flash white...
Per saperne di piùI have a core duo macbook that i'm working on the when the power button is pressed the screen flickers really bright and...
Per saperne di piùI have a macbook that turns on by itself when the charger is connected it will go to a kernal panic when i get close to...
Per saperne di piùHow important is to re apply the black tape on the bottom of the logicboard that covers different intergrated circuits,...
Per saperne di piùPagina 1 di 2
Risposte
The heatsink is incomplete the sensor has been removed, you need another one. The temperature sensor hangs just to the right of the fins on the copper bar.
Per saperne di piùYes it will fit yours. The 2.2 ,2.4 ,2.5 and 2.6ghz all interchange.
Per saperne di piùIs the lcd still good? If so ... 1. Keep it you might need it for testing in the future. 2. Start learning how to refurbish cell phone screens and use this one as your first project. 3. Sell it to a local shop or on ebay.
Per saperne di piùNo sorry they are not cross compatible , for starters the screens are different a1212 uses CFL bulb , while the a1261 uses LED bulb.
Per saperne di piùYes. All parts compatible 2011 and 2012 .
Per saperne di piùNo they have way to many parts with most with different motherboard connections. A1226,A1260 LED display versions both compatible 2.2, 2.4, 2.5 and 2.6 processors all will swap between each other. The A1211 A1150 compatible to each other - they use the LCD display.
Per saperne di piùLemerise is right. That is your isight camera cable and unfortunately there is no fix for that, I repair on component level with a stereo microscope and it is nearly impossible to fix! Your only option is to pull the glass and replace the cable or buy a used display and selling the old for parts if you wanted. That's it! See within the wire there are 10 strands that are microscopic if 1 of them is not together with the rest it will not work so your working on 2 wires the outer and the inner with 10 and there is four wires total.
Per saperne di piùTrying to tell you exactly what chip needing replacing is toooo vast! It could be the chip, resistors ,caps or inductors or even shorted traces that require jumps. You need to search the net for boardview and schematic for your board and check for short to ground with multimeter youtube can help if you look right. No light on the magsafe usually means the one wire over voltage is not working , feel around on the board and see also if there is area that is super super hot obviously this means the circuit is shorted. That's all I can do this is a very simple answer to a very in depth answer. Good luck!
Per saperne di piùWith the Mac off and battery disconnected pop off the stuck key examine the clip, for good measure take rubbing alcohol and scrub with a toothbrush , fasten key at see if it still sticks.
Per saperne di piùThe battery goes into a fail safe mode by expanding and not exploding you need another battery make sure it's a Apple original , knockoffs will cause problems.
Per saperne di piùPagina 1 di 12