Salta al contenuto principale

Aggiusta la tua roba

Diritto alla Riparazione

Componenti & Strumenti

Introduzione

This guide shows how to apply display assembly adhesive to an opened iPad. Use it to prepare your display assembly before resealing your device during a repair.

  1. Before installing new adhesive, thoroughly clean the display assembly and the frame of all residue. Use tweezers to pull up sections of tape residue.
    • Before installing new adhesive, thoroughly clean the display assembly and the frame of all residue.

    • Use tweezers to pull up sections of tape residue.

    • Use an opening tool or a spudger to scrape residue off. You can use high concentration (over 90%) isopropyl alcohol to soften the adhesive.

    • Remove the residue by wiping in one direction to prevent smearing.

    • Do not scrape with a metal tool, or you will scratch the display assembly's surface.

  2. Lay out the replacement adhesive strips around the display assembly so that they correspond to the correct sides.
    • Lay out the replacement adhesive strips around the display assembly so that they correspond to the correct sides.

  3. Each adhesive strip is encased in four layers of plastic—three on top and one on the bottom. Peel and remove the topmost plastic cling layer from the left adhesive strip.
    • Each adhesive strip is encased in four layers of plastic—three on top and one on the bottom.

    • Peel and remove the topmost plastic cling layer from the left adhesive strip.

    • Peel and remove the bottom plastic liner from the strip.

    • The top of the adhesive strip should still be covered by a colored plastic layer as well as a clear plastic stiffening layer.

    • The bottom of the adhesive strip should now be exposed and sticky.

  4. If there are extra bits of adhesive on the strips that are not required for your particular model of iPad, remove them now. If there are extra bits of adhesive on the strips that are not required for your particular model of iPad, remove them now.
    • If there are extra bits of adhesive on the strips that are not required for your particular model of iPad, remove them now.

  5. Kit per Nintendo Switch

    A quick fix to get back in the game

    Shop Switch Kits

    Kit per Nintendo Switch

    A quick fix to get back in the game

    Shop Switch Kits
  6. Align the left adhesive strip to the left edge of the display assembly. Beginning from one corner, lay the adhesive strip onto the display assembly and press the strip into place. If necessary, use a spudger to press down the narrow parts of the adhesive strip.
    • Align the left adhesive strip to the left edge of the display assembly.

    • Beginning from one corner, lay the adhesive strip onto the display assembly and press the strip into place.

    • If necessary, use a spudger to press down the narrow parts of the adhesive strip.

  7. Repeat the process with the right adhesive strip. Peel and remove the topmost cling layer from the strip. Peel and remove the bottom liner layer from the strip.
    • Repeat the process with the right adhesive strip.

    • Peel and remove the topmost cling layer from the strip.

    • Peel and remove the bottom liner layer from the strip.

    • Align the adhesive strip to the right edge of the display assembly.

    • Starting from one corner, lay the adhesive strip onto the display assembly and press in place.

  8. Repeat the process for the top adhesive strip. Peel and remove the topmost cling layer from the strip. Peel and remove the bottom liner from the strip.
    • Repeat the process for the top adhesive strip.

    • Peel and remove the topmost cling layer from the strip.

    • Peel and remove the bottom liner from the strip.

    • Align the strip to the top of the display assembly such that the straight adhesive line bridges the gap between the left and right strips.

    • Press the strip in place.

  9. Repeat the process for the bottom adhesive strip. Peel and remove the topmost cling layer from the strip. Peel and remove the bottom liner from the strip.
    • Repeat the process for the bottom adhesive strip.

    • Peel and remove the topmost cling layer from the strip.

    • Peel and remove the bottom liner from the strip.

    • Align the strip to the bottom of the display assembly such that the straight adhesive line bridges the gap between the left and right strips.

    • Press the strip in place.

  10. Peel and remove the clear plastic stiffening layer from all four adhesive strip sections. Peel and remove the clear plastic stiffening layer from all four adhesive strip sections. Peel and remove the clear plastic stiffening layer from all four adhesive strip sections.
    • Peel and remove the clear plastic stiffening layer from all four adhesive strip sections.

  11. Continue with the reassembly process until you are ready to seal the device.
    • Continue with the reassembly process until you are ready to seal the device.

  12. Peel and remove the four colored plastic liners to expose the adhesive. Close the device and place something heavy,  such as a stack of large books, on top for thirty minutes to help the new adhesive bond.
    • Peel and remove the four colored plastic liners to expose the adhesive.

    • Close the device and place something heavy, such as a stack of large books, on top for thirty minutes to help the new adhesive bond.

Conclusione

Repair didn’t go as planned? Check out our Answers Community for troubleshooting help.

Tarun Thiruma

Membro da: 20/11/2019

2.105 Reputazione

14 Guide realizzate

Team

iFixit Membro di iFixit

Community

107 Membri

10.301 Guide realizzate

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 10

Ultimi 30 Giorni: 39

Tutti i Tempi: 99