Questa versione può contenere modifiche errate. Passa all'ultima istantanea verificata.
Introduzione
Segui questa guida per eseguire l'upgrade della CPU.
Cosa ti serve
-
-
Allentare le tre viti con testa a croce che fissano lo sportello di accesso al bordo inferiore dell'iMac.
-
Rimuovere lo sportello di accesso dall'iMac.
-
-
Attrezzo utilizzato in questo passaggio:Heavy-Duty Suction Cups (Pair)$14.95
-
Fai aderire una ventosa accanto a ciascuno dei due angoli superiori del pannello di vetro.
-
Se la ventosa non aderisce, prova a ripulire il pannello di vetro e la ventosa con un solvente delicato.
-
-
-
Solleva il pannello di vetro in perpendicolare rispetto alla superficie dello schermo LCD, affinché sia possibile liberare i piedini di montaggio in acciaio inseriti lungo il lato sottostante al bordo superiore del pannello di vetro.
-
Estrai il panello di vetro dal bordo inferiore dell'iMac e mettilo da parte con attenzione.
-
-
-
Rimuovi le otto viti Torx T10 da 8 mm che fissano il display al case esterno.
-
-
-
Rimuovi le quattro viti che fissano l'alimentatore al case esterno:
-
Due viti Torx T10 a passo fine da 22,2 mm
-
Una vite Torx T10 a passo grosso da 25 mm
-
Una vite Torx T10 a passo grosso da 9 mm
-
-
-
Con molta attenzione solleva ed estrai l'alimentatore dal case esterno e fallo ruotare fino a scoprire il connettore come in figura, tenendo presente che il cavo della tensione di uscita è ancora collegato alla macchina.
-
Per scollegare il cavo di ingresso della tensione premi sul sistema di bloccaggio del connettore ed estrai il connettore stesso dalla presa sul circuito stampato.
-
Una volta estratto, tieni il connettore distante dall'alimentatore.
-
-
-
Tira fuori dal suo zoccolo sulla scheda madre il connettore del sensore termico dell'unità ottica.
-
-
-
-
Solleva dal bordo interno il disco ottico e fai passare il suo connettore oltre il telaio attaccato alla scheda logica.
-
Spingi con attenzione il disco ottico fuori dai suoi pin di montaggio sul bordo del case esterno in modo da avere spazio per disconnettere il cavo del disco ottico.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the single 13 mm T10 Torx screw securing the optical drive fan to the outer case.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Pull the optical drive off the pins attached to the outer case.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Pull the optical drive fan connector away from its socket on the logic board.
-
Remove the optical drive fan from the iMac.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Pull the left and right speaker connectors toward the right side of the iMac to disconnect them from the logic board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Disconnect the audio port cable by pulling its connector toward the right side of the iMac.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Disconnect the AirPort cable by lifting its connector off the socket on the logic board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Disconnect the following cables by pulling their connectors toward the top edge of the iMac:
-
Camera cable
-
Hard drive thermal sensor
-
Hard drive fan
-
Microphone
-
Disconnect the following cables by pulling their connectors toward the right edge of the iMac:
-
Ambient temperature sensor
-
Bluetooth cable
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Disconnect the CPU fan and power button by pulling their connectors toward the left edge of the iMac.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
If present, remove the piece of tape covering the IR sensor connector.
-
Disconnect the IR sensor by pulling its connector toward the top edge of the iMac.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use your fingers to lift IR sensor assembly straight up out of the outer case.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the following six screws securing the logic board to the outer case:
-
Three 25 mm T10 Torx
-
Two 21.5 mm T10 Torx
-
One 7 mm T10 Torx
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the plastic ducts from the side of the LED driver board and the hard drive by pulling them away from the outer case.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Carefully remove the aluminum tape attaching the GPU heat sink to the outer case.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Carefully pull the logic board slightly away from the outer case.
-
While holding the board away from the outer case, rotate the board back and forth while lifting up to release it from the outer case.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Now that the lower edge of the board is free from the outer case, rotate the logic board toward yourself to expose its rear face.
-
Carefully pull the optical drive connector away from its socket on the logic board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Disconnect the DC-In cable from the logic board by simultaneously depressing the locking lever on the connector while pulling it away from its socket.
-
Remove the logic board from the outer case.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a pair of tweezers to lift the heat sink thermal sensor connector straight up out of its socket on the logic board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the following six screws securing the heat sink to the logic board:
-
Five 6.5 mm T8 Torx
-
One 7 mm T10 Torx
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Lift the heat sink bracket off the logic board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Carefully lift the logic board off the heat sink.
-
-
-
Con molta attenzione, tira via la barra di blocco della CPU dalla presa della CPU.
-
Ruota la barra verso il centro della scheda logica.
-
Per rimontare il tuo dispositivo, segui le istruzioni in ordine inverso.
Per rimontare il tuo dispositivo, segui le istruzioni in ordine inverso.
Annulla: non ho completato questa guida.
Altre 30 persone hanno completato questa guida.
Un ringraziamento speciale a questi traduttori:
100%
Questi traduttori ci stanno aiutando ad aggiustare il mondo! Vuoi partecipare?
Inizia a tradurre ›
19 Commenti
Hello I fixit.!
Hello a lot of congrats! for your site! is very very helpfully for Mac Users
so. i have a question please if you want to help me.!
i have an i mac 21,5 late2009
3,06ghz intel core 2 duo
i have an idea to change the processor to. intel core i5 3,3 Ghz core
can be compatible . on main board .
thanks a lot for your time
These 21.5" (and 27") iMacs came with only either Core 2 Duo E7600 (3.06Ghz, 2 core, 65W TDP, LGA 775) or Core 2 Duo E8600 (3.33GHz, 2 core, 65W TDP, LGA 775), which are incompatible with any Core i5 as there are no Core i5's that were available on the LGA 775 socket these systems.
You might be able to upgrade to a Core 2 Quad Q9505S or Q9550S (2.83GHz, 4 core, 65W TDP LGA 775) which would provide 2 extra cores than the E7600/E8600 and work in the same socket but drop the max clocks to stay at the same 65W TDP power limit.
I installed a Q6700 Core 2 Quad into my late 2009 Core 2 Duo iMac.
Sadly it is not working, only recognize 2 Cores instead 4 under Windows 7.
Booting in the lates Mac OS, it gives up Kernel panic.
Any advise?
The Core 2 Quad Q6700 is a 105W TDP processor and the 21.5" & 27" iMacs running the Core 2 Duo E7600/E8600 only support 65W TDP LGA 775 Core 2 processors. If you wish to upgrade from the Core 2 Duo E7600/E8600 to a Core 2 Quad in these systems; I would recommend wither the Q9505S or Q9550S - specifically the "S" on there as those are the 65W TDP versions of the 105W TDP Q9505 and Q9550.
Windows is only allowing 2 of the 4 cores of that Q6700 to run to fit within the TDP of the system (particularly by regulating how much power the CPU can draw), and MacOS is panicking as it doesn't know how to handle the 105W the Q6700 is asking for on a 65W system.
Hello,
I'd like to upgrade the Core 2 Duo 3.06 CPU of my iMac 10,1 21.5". I already done the same operation in a white Core Duo iMac, being able to install the unsupported OS X 10.7. I'd like to do the same on the 10,1 but what CPU can I install? It seems that the i3, i5 or i7 are phisically different, am I right? And the user Tim report in being unable to make it work with a Core 2 Quad. So... what are the possibilities? Thanks!