Aggiusta la tua roba

Diritto alla Riparazione

Store

PlayStation 2 Slimline SCPH-7500x Fan Replacement

Scritto Da: Jared Hirata (e 15 altri collaboratori)
  • Commenti: 1
  • Preferiti: 6
  • Completamenti: 2

Difficoltà

Moderato

Passi

10

Tempo Necessario

15 minuti

Sezioni

2

Contrassegni

3

In Progress

In Lavorazione

Questa guida è un work in progress. Ricarica periodicamente per vedere le ultime modifiche!

Needs More Images

Necessarie Più Immagini

Con poche altre immagini, le procedure illustrate in questa guida sarebbero chiarissime.

Better Introduction

Introduzione Migliore

Migliora questa guida completando o revisionando la sua introduzione.

Introduzione

This guide will walk you through a step-by-step process on how to properly remove and install the fan in the PlayStation 2 Slimline.

    • Turn off the PlayStation 2 (or PS2) and carefully unplug from the power source. Check to see there are no discs inside the console before flipping the game system upside-down.

    Traduci

  2. Locate the six feet on the bottom of the PS2.

    • Locate the six feet on the bottom of the PS2.

    • Five of the feet are in plain sight and one of the feet is located under the black void sticker on the bottom of the device.

    • Some versions of the console, such as the PAL Version, may not have this sticker. In this case, the foot or even the screw should be in plain sight.

    Traduci

  3. Pry apart the five visible feet from the bottom of the device using a spudger, or your fingers. Pry apart the five visible feet from the bottom of the device using a spudger, or your fingers. Pry apart the five visible feet from the bottom of the device using a spudger, or your fingers.

    • Pry apart the five visible feet from the bottom of the device using a spudger, or your fingers.

    Traduci

  4. The sixth foot is located under the black VOID sticker. Remove the sticker before removing the foot underneath. The sixth foot is located under the black VOID sticker. Remove the sticker before removing the foot underneath.

    • The sixth foot is located under the black VOID sticker. Remove the sticker before removing the foot underneath.

    Traduci

  6. After all of the feet have been removed, Use a Phillips #1 screwdriver to remove the six 4.0mm screws from the base of the PS2. After all of the feet have been removed, Use a Phillips #1 screwdriver to remove the six 4.0mm screws from the base of the PS2. After all of the feet have been removed, Use a Phillips #1 screwdriver to remove the six 4.0mm screws from the base of the PS2.

    • After all of the feet have been removed, Use a Phillips #1 screwdriver to remove the six 4.0mm screws from the base of the PS2.

    Traduci

  7. Once all of the screws have been removed, pull apart the top plastic cover from the bottom plastic cover. Start by lifting the side containing the power cable and Ethernet port. Then, lift the opposite side to fully separate. It will take force to pull apart the two halves. Once all of the screws have been removed, pull apart the top plastic cover from the bottom plastic cover. Start by lifting the side containing the power cable and Ethernet port. Then, lift the opposite side to fully separate. It will take force to pull apart the two halves. Once all of the screws have been removed, pull apart the top plastic cover from the bottom plastic cover. Start by lifting the side containing the power cable and Ethernet port. Then, lift the opposite side to fully separate. It will take force to pull apart the two halves.

    • Once all of the screws have been removed, pull apart the top plastic cover from the bottom plastic cover. Start by lifting the side containing the power cable and Ethernet port. Then, lift the opposite side to fully separate. It will take force to pull apart the two halves.

    Traduci

  8. If done correctly, you should have a fully detached plastic backing, revealing the electronic components of the PlayStation 2.

    • If done correctly, you should have a fully detached plastic backing, revealing the electronic components of the PlayStation 2.

    Traduci

  9. Locate the fan component of the motherboard of the PS2. With your fingers or tweezers, peel off the sticker that holds down the fan's wiring. With your fingers or tweezers, peel off the sticker that holds down the fan's wiring.

    • Locate the fan component of the motherboard of the PS2.

    • With your fingers or tweezers, peel off the sticker that holds down the fan's wiring.

    Traduci

  10. With tweezers, detach the terminal (white covering) to the red and yellow cords from the motherboard to the fan. With tweezers, detach the terminal (white covering) to the red and yellow cords from the motherboard to the fan.

    • With tweezers, detach the terminal (white covering) to the red and yellow cords from the motherboard to the fan.

    Traduci

  11. Locate and unscrew the three 1.6mm screws located next to the base of the fan. They are located off the curved edge of the fan.

    • Locate and unscrew the three 1.6mm screws located next to the base of the fan.

    • They are located off the curved edge of the fan.

    • Once you have removed the three screws, you are able to remove the fan from the PS2.

    Traduci
Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 2 persone hanno completato questa guida.

Autore

con 15 altri collaboratori

Jared Hirata

Membro da: 09/04/2013

600 Reputazione

7 Guide realizzate

Distintivi: 12

+9 altri distintivi

Team

Cal Poly, Team 17-4, Regan Spring 2013 Membro di Cal Poly, Team 17-4, Regan Spring 2013

CPSU-REGAN-S13S17G4

3 Membri

14 Guide realizzate

0 Commenti

Aggiungi un commento

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 1

Ultimi 7 Giorni: 6

Ultimi 30 Giorni: 29

Tutti i Tempi: 2,466