Aggiusta la tua roba Comunità Store

Motorola Moto Z2 Force Screen Replacement

Introduzione

The display assembly for the Motorola Moto Z2 Force includes the front facing camera flash and the fingerprint sensor. The fingerprint sensor is very difficult to remove from the display assembly and will most likely end up damaging the screen, so it may be a good idea to replace the entire assembly should the sensor malfunction.

Cosa ti serve

  1. Motorola Moto Z2 Force Screen Replacement, Display Assembly: passo 1, immagine 1 di 1

    • Place the phone on a flat surface with the screen facing up.

    • Insert the flat end of a nylon spudger into the crease separating the screen and the body in the lower right corner of the phone.

    • Pry open part of the screen by pulling the tool and the screen toward you.

    • You may be required to use a heating element, such as the iOpener, to heat and loosen the adhesive underneath before attempting to pry it open.

    Traduci

  2. Motorola Moto Z2 Force Screen Replacement: passo 2, immagine 1 di 3 Motorola Moto Z2 Force Screen Replacement: passo 2, immagine 2 di 3 Motorola Moto Z2 Force Screen Replacement: passo 2, immagine 3 di 3

    • Wedge the plastic opening tool between the gap created by separating the screen and body of the phone in the right hand corner to hold it open.

    • Insert the nylon spudger into the lower left corner of the screen and pry the screen toward you.

    • Continue to insert the plastic opening and spudger tools around the phone, and pry open the screen until it is fully separated from the device.

    • It is possible to pry the display assembly apart at this step. Be sure to get the prying instruments underneath both the LCD and screen layers of the display assembly to ensure this separation does not occur.

    Traduci

  4. Motorola Moto Z2 Force Screen Replacement: passo 3, immagine 1 di 2 Motorola Moto Z2 Force Screen Replacement: passo 3, immagine 2 di 2

    • Remove the screen by pulling from right to left and placing the screen face down on the flat surface next to the main body of the device.

    Traduci

  5. Motorola Moto Z2 Force Screen Replacement: passo 4, immagine 1 di 2 Motorola Moto Z2 Force Screen Replacement: passo 4, immagine 2 di 2

    • Using the flat end of the nylon spudger, pull off the black tape on top of the screen connector piece that the black ribbon is attached to.

    Traduci

  6. Motorola Moto Z2 Force Screen Replacement: passo 5, immagine 1 di 2 Motorola Moto Z2 Force Screen Replacement: passo 5, immagine 2 di 2

    • Insert the black spudger under the lock of the latch connecting the black ribbon of the screen to the phone body.

    • Pull up on the lock to unlock the latch.

    • Separate the black ribbon from the latch by pulling gently to the left.

    Traduci
Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 17 persone hanno completato questa guida.

Autore

con 8 altri collaboratori

Amelia Fruda

Membro da: 01/24/18

669 Reputazione

2 Guide realizzate

Distintivi: 11

+8 altri distintivi

Team

Cal Poly, Team S2-G1, Livingston Winter 2018 Membro di Cal Poly, Team S2-G1, Livingston Winter 2018

CPSU-LIVINGSTON-W18S2G1

4 Membri

26 Guide realizzate

14 Commenti

What about installing the new screen?

John - Replica

lol exactly what i was thinking, john!!

like what the !&&*….guide us thru removing the entire screen and then just leave us with our d in our hand lol

PETE ZITO - Replica

Just do the same thing backwards.

Jade Davis -

Can I use a z2 play screen on the z2 force?

Paulo Alberto Werhli Meier - Replica

You can but they have a big difference the LCD pixelation. The Z2 Force has 2,560x1,440 pixel resolution while the play has a 1,920x1,080 resolution. So even thought it can be done it is not recommended.

Cole Jensen -

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 3

Ultimi 7 Giorni: 8

Ultimi 30 Giorni: 53

Tutti i Tempi: 18,091