Questa versione può contenere modifiche errate. Passa all'ultima istantanea verificata.
Cosa ti serve
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Insert a SIM eject tool, SIM eject bit, or a straightened paperclip into the small hole in the SIM card tray.
-
Press to eject the tray.
-
Remove the SIM card tray assembly from the phone.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Heat an iOpener and apply it to the top edge of the phone for a minute.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Angle an opening pick and firmly press so that it slips under the back cover.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Slide the opening pick along the top edge of the phone to break up the adhesive.
-
Use the pick to release the deeper areas but avoid slicing through the camera bezel area.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Repeat the iOpener heating and slicing procedures for the remaining three sides.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Once you have cut through the adhesive, slowly peel the back cover away from the frame.
-
Remove the back cover.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Insert an opening pick under the flash connector rubber cover and pry forward to remove it.
-
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the point of a spudger to pry up and remove the coil connector rubber cover.
-
To reinstall the cover, align the cover and use your finger to push it forward into place.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the point of a spudger to pry up and disconnect the flash connector.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the point of a spudger to pry up and disconnect the wireless charging coil connector.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the following T3 screws securing the midframe:
-
Thirteen 3.1 mm black screws
-
Four 4.3 mm silver screws
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Insert an opening pick along the frame seam and twist slightly to release the midframe from the phone.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Carefully peel the black graphite layer from the phone.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the two 4.2 mm T3 screws securing the metal bracket adjacent to the battery.
-
Remove the metal bracket.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the point of a spudger to pry up and disconnect the battery pack connector.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Angle and insert an opening pick under the long edge of the battery away from the motherboard side.
-
Insert a second opening pick along the same battery edge next to the first pick.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Apply firm, constant prying pressure to the picks to release the battery from the frame.
-
As the battery loosens from the frame, move the picks inward and continue to pry upwards.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
Attrezzo utilizzato in questo passaggio:Tesa 61395 Tape$5.99-
Remove the battery.
-
To help with alignment, connect the battery temporarily to the motherboard before adhering it in place. Disconnect the battery before you continue with re-assembly.
-
Annulla: non ho completato questa guida.
Altre 78 persone hanno completato questa guida.
30 Commenti
Despite being careful, I lost one screw that seemingly disappeared as I tried to place it back. Even a rare earth magnet didn't find it. It would be nice to have spare screws.
From whom would get those?
Your neighbors Turbo 2…it would've up to you whether or not to tell the neighbors that you got them, lol. Everyone seems to have a junk phone around, open it up and find the closest matching one….. I be yet to find anyone that sells spare phone
Replaced the battery, but now the display is pixelated on the right side. Any ideas? Need help ASAP.
The only thing that got me hung up on this was the volume button reassembly. I can't seem to get the volume button to work properly again.