Aggiusta la tua roba Comunità Store

Levoit Core 300-RAC Fan Replacement

Introduzione

A non-functioning fan will severely limit your Levoit Core 300-RAC air purifier's performance. If your device is not outputting enough air, or the fan doesn't seem to be spinning, then it may be time to replace the fan. These are steps on how you would replace the fan.

Cosa ti serve

  1. Levoit Core 300-RAC Fan Replacement, Air Filter: passo 1, immagine 1 di 2 Levoit Core 300-RAC Fan Replacement, Air Filter: passo 1, immagine 2 di 2

    • Make sure your device is turned off and unplugged for safety.

    • Turn the Levoit Core 300-RAC over so the bottom is facing up.

    Modifica

  2. Levoit Core 300-RAC Fan Replacement: passo 2, immagine 1 di 3 Levoit Core 300-RAC Fan Replacement: passo 2, immagine 2 di 3 Levoit Core 300-RAC Fan Replacement: passo 2, immagine 3 di 3

    • Turn the bottom cover counterclockwise and lift it off to remove it.

    • The cover does not "snap" on or off when turned.

    Modifica

  3. Levoit Core 300-RAC Fan Replacement: passo 3, immagine 1 di 3 Levoit Core 300-RAC Fan Replacement: passo 3, immagine 2 di 3 Levoit Core 300-RAC Fan Replacement: passo 3, immagine 3 di 3

    • Lift the filter straight up and out of the device.

    Modifica

  4. Levoit Core 300-RAC Fan Replacement, Fan: passo 4, immagine 1 di 3 Levoit Core 300-RAC Fan Replacement, Fan: passo 4, immagine 2 di 3 Levoit Core 300-RAC Fan Replacement, Fan: passo 4, immagine 3 di 3

    • Use a Phillips #2 screwdriver to remove the four screws that secure the gray lid towards the base of the device.

    • Set the screws aside in a safe place.

    Modifica

  5. Levoit Core 300-RAC Fan Replacement: passo 5, immagine 1 di 3 Levoit Core 300-RAC Fan Replacement: passo 5, immagine 2 di 3 Levoit Core 300-RAC Fan Replacement: passo 5, immagine 3 di 3

    • Use a metal spudger or Jimmy to gently pry between the four white tabs and the white housing to release the outer housing.

    • Gently pulling up on the outer housing can prevent the clips from resetting.

    Modifica

  6. Levoit Core 300-RAC Fan Replacement: passo 6, immagine 1 di 2 Levoit Core 300-RAC Fan Replacement: passo 6, immagine 2 di 2

    • Remove the outer white housing and set it to the side.

    • The power cord is fed through a hole in the side of this housing, so it has to sit right next to the device.

    Modifica

  8. Levoit Core 300-RAC Fan Replacement: passo 7, immagine 1 di 3 Levoit Core 300-RAC Fan Replacement: passo 7, immagine 2 di 3 Levoit Core 300-RAC Fan Replacement: passo 7, immagine 3 di 3

    • Grab the cable channel by its base, squeeze, and pull up at the same time to remove it.

    Modifica

  9. Levoit Core 300-RAC Fan Replacement: passo 8, immagine 1 di 2 Levoit Core 300-RAC Fan Replacement: passo 8, immagine 2 di 2

    • Remove the four Phillips #2 screws securing the gray face plate.

    • Set the screws aside in a safe place.

    Modifica

  10. Levoit Core 300-RAC Fan Replacement: passo 9, immagine 1 di 3 Levoit Core 300-RAC Fan Replacement: passo 9, immagine 2 di 3 Levoit Core 300-RAC Fan Replacement: passo 9, immagine 3 di 3

    • Insert a Jimmy or spudger between the white tab and the gray faceplate body to release the faceplate.

    • Lift it out.

    Modifica

  11. Levoit Core 300-RAC Fan Replacement: passo 10, immagine 1 di 1

    • Turn your device over so it is upright again.

    Modifica

  12. Levoit Core 300-RAC Fan Replacement: passo 11, immagine 1 di 3 Levoit Core 300-RAC Fan Replacement: passo 11, immagine 2 di 3 Levoit Core 300-RAC Fan Replacement: passo 11, immagine 3 di 3

    • Insert the Jimmy between the gray grille cover and the top of the device.

    • Work your way around the grille cover with the Jimmy to release the clips holding it in place.

    • Take note of the placement of the tabs, as they are keyed and need to go back in the exact way they came out.

    • Remove the grille cover gently as it is connected by a ribbon cable.

    • Be careful not to put too much strain on the ribbon cable as it may break.

    Modifica

  13. Levoit Core 300-RAC Fan Replacement: passo 12, immagine 1 di 3 Levoit Core 300-RAC Fan Replacement: passo 12, immagine 2 di 3 Levoit Core 300-RAC Fan Replacement: passo 12, immagine 3 di 3

    • Squeeze the tab on the connector to release the bundled cable from the control board.

    • The connector should come out fairly easily, do not force it. Pulling too hard could damage the connector.

    Modifica

  14. Levoit Core 300-RAC Fan Replacement: passo 13, immagine 1 di 3 Levoit Core 300-RAC Fan Replacement: passo 13, immagine 2 di 3 Levoit Core 300-RAC Fan Replacement: passo 13, immagine 3 di 3

    • Insert a spudger or Jimmy into the four tabs to release them from holding the outer white housing to the inner black core.

    • Remove the white outer housing.

    Modifica

  15. Levoit Core 300-RAC Fan Replacement: passo 14, immagine 1 di 1

    • Flip your device over again so the fan is facing up.

    Modifica

  16. Levoit Core 300-RAC Fan Replacement: passo 15, immagine 1 di 2 Levoit Core 300-RAC Fan Replacement: passo 15, immagine 2 di 2

    • Use a Phillips #2 screwdriver to remove the three screws on the upper portion of the black housing.

    • Set the screws aside in a safe place.

    Modifica

  17. Levoit Core 300-RAC Fan Replacement: passo 16, immagine 1 di 3 Levoit Core 300-RAC Fan Replacement: passo 16, immagine 2 di 3 Levoit Core 300-RAC Fan Replacement: passo 16, immagine 3 di 3

    • Remove the upper portion of the black housing.

    Modifica

  18. Levoit Core 300-RAC Fan Replacement: passo 17, immagine 1 di 3 Levoit Core 300-RAC Fan Replacement: passo 17, immagine 2 di 3 Levoit Core 300-RAC Fan Replacement: passo 17, immagine 3 di 3

    • Use a 13mm socket wrench with an extension to remove the nut holding the fan in place and remove all hardware from the threaded shaft.

    • There should be a nylon-insert lock nut, a flat washer, and a split ring washer. Set these aside in a safe location.

    Modifica

  19. Levoit Core 300-RAC Fan Replacement: passo 18, immagine 1 di 3 Levoit Core 300-RAC Fan Replacement: passo 18, immagine 2 di 3 Levoit Core 300-RAC Fan Replacement: passo 18, immagine 3 di 3

    • Lift the fan up and off of the threaded shaft.

    • There is another washer underneath the fan, leave it in place for the replacement fan.

    Modifica
Conclusione

To reassemble your device, follow these instructions in reverse order.

Autore

con 3 altri collaboratori

Stephen Carrozza

Membro da: 11/01/23

241 Reputazione

1 Guida realizzata

Distintivi: 3

Team

UMass Dartmouth, Team 1-6, Petersen Fall 2023 Membro di UMass Dartmouth, Team 1-6, Petersen Fall 2023

UMASSD-PETERSEN-F23S1G6

5 Membri

6 Guide realizzate

0 Commenti

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 2

Ultimi 7 Giorni: 31

Ultimi 30 Giorni: 135

Tutti i Tempi: 532