Salta al contenuto principale

Hytera TC-580 Microphone Replacement

Cosa ti serve

  1. Hytera TC-580 Microphone Replacement, Battery: passo 1, immagine 1 di 2 Hytera TC-580 Microphone Replacement, Battery: passo 1, immagine 2 di 2
    • Remove the two 10mm Phillips #0 from the belt clip.

  2. Hytera TC-580 Microphone Replacement: passo 2, immagine 1 di 2 Hytera TC-580 Microphone Replacement: passo 2, immagine 2 di 2
    • Push in the release button and pull up on the battery to remove.

  3. Hytera TC-580 Microphone Replacement, Antenna: passo 3, immagine 1 di 1
    • Twist antenna counter-clockwise and set damaged antenna aside.

  4. Hytera TC-580 Microphone Replacement, Keypad: passo 4, immagine 1 di 1
    • Remove the volume knob by firmly lifting up on both sides of it.

  5. Hytera TC-580 Microphone Replacement: passo 5, immagine 1 di 1
    • Remove the orange o-ring around volume knob using tweezers.

  6. Hytera TC-580 Microphone Replacement: passo 6, immagine 1 di 1
    • Remove grey nut from base of volume knob by turning it counterclockwise with a set of tweezers.

  7. Hytera TC-580 Microphone Replacement: passo 7, immagine 1 di 1
    • Remove the brass washer from the base of the antenna slot by turning it counterclockwise with a set of tweezers.

  8. Hytera TC-580 Microphone Replacement: passo 8, immagine 1 di 2 Hytera TC-580 Microphone Replacement: passo 8, immagine 2 di 2
    • Remove the two 15mm T8 Torx screws from the base of the battery cavity.

  9. Hytera TC-580 Microphone Replacement: passo 9, immagine 1 di 1
    • Using a plastic opening tool, pry in between the plastic case and metal circuit board to remove the board.

  10. Hytera TC-580 Microphone Replacement: passo 10, immagine 1 di 1
    • Peel off the keypad by hand.

  11. Hytera TC-580 Microphone Replacement, Speaker: passo 11, immagine 1 di 3 Hytera TC-580 Microphone Replacement, Speaker: passo 11, immagine 2 di 3 Hytera TC-580 Microphone Replacement, Speaker: passo 11, immagine 3 di 3
    • Remove eleven 4mm Phillips #00 screws.

  12. Hytera TC-580 Microphone Replacement: passo 12, immagine 1 di 1
    • Apply a soldering iron to the solder joints to remove the two wires connecting the speaker to the circuit board.

  13. Hytera TC-580 Microphone Replacement, Microphone: passo 13, immagine 1 di 1
    • If not already done, remove the circuit board completely from the case.

  14. Hytera TC-580 Microphone Replacement: passo 14, immagine 1 di 1
    • Desolder the two microphone solder joints.

  15. Hytera TC-580 Microphone Replacement: passo 15, immagine 1 di 1
    • The microphone should fall out after all the solder has been removed.

Conclusione

To reassemble your device, follow these instructions in reverse order.

Stuart

Membro da: 02/14/18

464 Reputazione

3 Guide realizzate

Team

USF Tampa, Team S3-G4, Nance Spring 2018 Membro di USF Tampa, Team S3-G4, Nance Spring 2018

USFT-NANCE-S18S3G4

3 Membri

5 Guide realizzate

0 Commenti

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 2

Ultimi 30 Giorni: 8

Tutti i Tempi: 703