Introduzione

This guide will instruct you how to remove the back panel of your camera.

Using a #00 Phillips screw driver, remove three 4.4 mm Phillips screws as indicated by the red circles.
  • Using a #00 Phillips screw driver, remove three 4.4 mm Phillips screws as indicated by the red circles.

Aggiungi Commento

Using your finger, peel back the textured grip so the components are separated. Using your finger, peel back the textured grip so the components are separated.
  • Using your finger, peel back the textured grip so the components are separated.

Aggiungi Commento

Using the flat end of a spudger, loosen the connection between the front panel and the device. Remove the front panel using your hands. Remove the front panel using your hands.
  • Using the flat end of a spudger, loosen the connection between the front panel and the device.

  • Remove the front panel using your hands.

Aggiungi Commento

Turn Camera over.
  • Turn Camera over.

  • Using a #00 Phillips screw driver, unscrew the two 4.9 mm Phillips screws located on either side of the viewfinder.

Aggiungi Commento

Using a #00 Phillips screw driver, unscrew the one 5.7 mm Phillips screw located next to the LCD screen.
  • Using a #00 Phillips screw driver, unscrew the one 5.7 mm Phillips screw located next to the LCD screen.

Aggiungi Commento

Lay the camera on its back.
  • Lay the camera on its back.

  • Unsolder the flash connection from the motherboard as noted by the blue circle.

Aggiungi Commento

Remove the top panel by lifting it from the back, pushing it forward over the camera and letting it rotate down in front of the camera. Remove the top panel by lifting it from the back, pushing it forward over the camera and letting it rotate down in front of the camera. Remove the top panel by lifting it from the back, pushing it forward over the camera and letting it rotate down in front of the camera.
  • Remove the top panel by lifting it from the back, pushing it forward over the camera and letting it rotate down in front of the camera.

Aggiungi Commento

Using a #00 Philllips screw driver, unscrew the 6.8 mm Phillips screw that holds the strap anchor noted by the red circle.
  • Using a #00 Philllips screw driver, unscrew the 6.8 mm Phillips screw that holds the strap anchor noted by the red circle.

  • Remove the strap anchor.

Aggiungi Commento

Unlatch the back panel.
  • Unlatch the back panel.

  • Using a #00 Phillips screw driver, unscrew the six screws on the bottom of the camera.

    • One 7.4 mm Phillips screw

    • Two 6.0 mm Phillips screws

    • Two 4.4 mm Phillips screws

    • One 3.9 mm Phillips screw

Aggiungi Commento

From the bottom of the camera push the hinge rod in with your finger. Return the camera to its upright position. Use pliers (or tweezers) to pull the rod out from the top.
  • From the bottom of the camera push the hinge rod in with your finger.

  • Return the camera to its upright position.

  • Use pliers (or tweezers) to pull the rod out from the top.

Aggiungi Commento

Conclusione

To reassemble your device, follow these instructions in reverse order.

Zach

Membro da: 04/04/2012

40 Reputazione

8 Guide realizzate

Team

Cal Poly, Team 14-9, Forte Spring 2012 Membro di Cal Poly, Team 14-9, Forte Spring 2012

CPSU-FORTE-S12S14G9

5 Membri

12 Guide realizzate

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 2

Ultimi 30 Giorni: 10

Tutti i Tempi: 1,453