Trova le risposte in questo documento
Abbiamo letto tutte le pagine di 7, così non devi farlo tu. Chiedi e ottieni subito la risposta.
Factory Navigation Radio Installation Guide
Follow the instructions within this manual to remove your factory radio. Once removed, proceed with the navigation radio installation.
Refer to our YouTube demonstration video or our in-depth installation guide located within the navigation radio's product page (on our website).
| OPTION | MY SCENARIO - Follow the specific option below that applies to you | INSTALL PROCEDURE - Follow the steps listed below |
| 1 | I am replacing an existing defective or missing factory navigation radio | The replacement factory navigation radio we send you will plug & play without any extra installation steps |
| 2 | I have a vehicle with Bose $ ^{®} $ and I am upgrading to the factory navigation radio. The front speaker grilles in my vehicle have the Bose $ ^{®} $ logo and my glove box label has the code "UQA" or "UQS" | Install the GPS antenna just under your windshield beneath your upper dash panel, then route the blue connector to the radio cubby. Carefully connect the VSS harness wire using the provided T-Tap to the "Junction Block - Left I/P" under the dash on the driver's side. (VSS is available on plug X2 pin H1 / green wire with a white trace) Then route the VSS radio connector to the radio cubby. Install our pre-programmed navigation radio along with the existing factory radio wiring harnesses (including the newly installed GPS antenna connector and VSS harness connector) |
| 3 | I have confirmed my vehicle does not have Bose and I am upgrading to the factory navigation radio | Install the amplifier and its associated wiring harness. Install the GPS antenna just under your windshield beneath your upper dash panel, then route the blue connector to the radio cubby. Carefully connect the VSS harness wire using the provided T-Tap to the "Junction Block - Left I/P" under the dash on the driver's side. (VSS is available on plug X2 pin H1 / green wire with a white trace) Then route the VSS radio connector to the radio cubby. Install our pre-programmed navigation radio along with the existing factory radio wiring harnesses (including the newly installed amplifier T-harness, the GPS antenna connector, and the VSS harness connector) |
Metra
Applications
Buick
Enclave .....2008-2012
Lucerne .....2006-2011
Chevrolet
Avalanche .....2007-up
Equinox .....2007-2009
Express Van .....2008-up
Impala .....2006-up
Monte Carlo .....2006-2007
Silverado $ ^{**} $ .....2007-up
Suburban .....2007-up
Tahoe .....2007-up
Traverse .....2009-up
Captiva Sport .....2012
GMC
Acadia ..... 2007-2012
Savanna ..... 2008-up
Sierra $ ^{} $ ..... 2007-up
Yukon XL Denali ..... 2007-up
Yukon/XL ..... 2007-up
Hummer
H2 ..... 2008-2009
Pontiac
Torrent ..... 2007-2009
Saturn
Outlook ..... 2007-2010
Vue ..... 2008-2010
Suzuki
XL-7 ..... 2007-2009
$ ^{} $Excluding classic models
Table of Contents
Table of Contents
Dash Disassembly
-
Buick Enclave 2008-2012 ..... 6
-
Buick Lucerne 2006-2011 ..... 3
-
Chevrolet Avalanche 2007-up ..... 3
-
Chevrolet Captiva Sport 2012.....7
-
Chevrolet Equinox 2007-2009.....5-6
-
Chevrolet Express Van (full size) 2008-up.....4
-
Chevrolet Impala 2006-up.....3
-
Chevrolet Monte Carlo 2006-2007.....3
-
Chevrolet Silverado Pickup (excluding classic models) 2007-up.....3
-
Chevrolet Suburban 2007-up.....3
-
Chevrolet Tahoe 2007-up.....3
-
Chevrolet Traverse 2009-up.....6
-
GMC Acadia 2007-2012.....6
-
GMC Savanna Van (full size) 2008-2010.....4
-
GMC Sierra (excluding classic models) 2007-up.....3
-
GMC Yukon/Yukon XL/Yukon XL Denali 2007-up.....3
-
Hummer H2 2008-2009.....7
-
Pontiac Torrent 2007-2009.....5-6
-
Saturn Outlook 2007-2010.....6
-
Saturn Vue 2008-2010.....7
-
Suzuki XL-7 2007-2009.....4-5
Caution: It is highly recommended to disconnect your vehicle's negative battery terminal prior to installation.
Buick Lucerne 2006-2011, Chevy Impala 2006-up, Monte Carlo 2006-2007
-
Unclip and remove the trim panel around radio and A/C control. (Figure A)
-
Remove (6) 9/32" screws to extract radio and A/C control from sub dash. (Figure B)
Continue to kit assembly
O
(Figure A)
0
Chevy Avalanche/Tahoe/Suburban/Silverado (excluding classic models) 2007-up, GMC Yukon/Sierra (excluding classic models) 2007-up
(Figure B)
-
Unclip and remove radio trim panel. (Figure A)
-
Remove (2) 8 mm screws securing switch panel below climate controls. Unplug and remove switch panel. (Figure B)
-
Remove (2) 8 mm screws securing climate controls. Unplug and remove climate controls. (Figure B)
-
Remove (4) 9/32" screws securing radio. Unplug and remove the radio. (Figure C)
Continue to kit assembly
