Trova le risposte in questo documento
Abbiamo letto tutte le pagine di 2, così non devi farlo tu. Chiedi e ottieni subito la risposta.
TP-Link TL-WR802N 300Mbps Wireless N Nano Router Quick Installation Guide
Quick Installation Guide
Operation Mode
300Mbps Wireless N Nano Router
| Scene | Operation Mode | Application |
| Travel | Wireless Router | To share a wired (Ethernet) connection to wireless devices, such as in a hotel room, small office and so on. |
| Hotspot Router | To create your personal Wi-Fi hotspot from a public Wi-Fi network such as in a hotel room, on a trade show and so on. | |
| Home | Range Extender | To extend the range of an existing Wi-Fi network. |
| Client | To enable your wired device (such as Blu-ray $ ^{\text{®}} $ players, smart TVs, or game consoles) to connect to a Wi-Fi network. | |
| Access Point | To transform an existing wired (Ethernet) network to a Wi-Fi network. |
7106506745 REV3.0.0
EAC MODEL NO. TL-WR802N
During Travel
Wireless Router (Default)
Internet
A B C
Hotspot Router
(( ) Public Wi-Fi
( ) A B
1 Connect the router according to Step A to C in the left diagram.
2 Use the default Wi-Fi Name and Wi-Fi Password printed on the Wi-Fi Info Card to connect to the router.
Check the internet connection on your laptop or smart phone, and please note that:
-
If you can access internet without any restriction, no other configuration is required.
-
If you're redirected to an authentication page, please complete it to access internet.
3 Launch a web browser and type http://tplinkwifi.net in the address bar. Enter admin (in lowercase) for both username and password.
4 Click Next to start the Quick Setup. Select Wireless Router and click Next.
5 Select the WAN Connection Type and follow the step-by-step instructions to configure the parameters. When using the router in a hotel room or a small office, please select Dynamic IP.
6 On the Wireless page, either keep the default Wireless Network Name and Wireless Password or customize them, and then click Next.
7 Click Finish to complete the configuration.
8 Please note the additional steps to be completed once the router is rebooted.
If you have changed the default Wi-Fi name and password, please reconnect your wireless devices to the new one.
1 Connect the router according to Step A to B in the left diagram.
2 Use the default Wi-Fi Name and Wi-Fi Password printed on the Wi-Fi Info Card to connect to the router.
3 Launch a web browser and type http://tplinkwifi.net in the address bar. Enter admin (in lowercase) for both username and password.
4 Click Next to start the Quick Setup. Select Hotspot Router and click Next.
5 Select the WAN Connection Type and follow the step-by-step instructions to configure the parameters. When using the router in a hotel room or a small office, please select Dynamic IP.
6 Select the public Wi-Fi that you want to connect to, and click Next.
7 Type in the public Wi-Fi's password. In the AP setting section, customize your Wi-Fi network name and password, then click Next.
8 Click Reboot to complete the configuration.
9 Please note the additional steps to be completed once the router is rebooted.
If you have changed the default Wi-Fi name and password, please reconnect your wireless devices to the new one.
Other Information
Router Ports and LED:
LED
| LED Status | Indication |
| Solid | The router is connected to the host Wi-Fi network or internet. |
| Blinking | Blinking steadily: The router is disconnected from the host Wi-Fi network or internet. Blinking irregularly: The router is booting or updating firmware. |
| Port | Description |
| LAN/WAN | Functions as the LAN port in Hotspot Router, Range Extender, Client and Access Point mode. Functions as the WAN port in Wireless Router mode. |
| Power | Connect to a USB charger, power adapter or computer USB port via the USB cable for power supply. |
| Reset | Use a pin to press and hold the Reset button for about five seconds until the LED blinks. |
