hp

Table of contents

aport DX115 kit installation ..... 1
Introduction ..... 1
Kit contents ..... 1
Before you begin ..... 1
Warnings and cautions ..... 2
Step 1—Preparing for component installation ..... 3
Accessing the internal components of the computer ..... 3
Step 2—Installing the DX115 case into the optical drive bay ..... 3
HP Z200 SFF and HP Z210 SFF computers ..... 4
HP Z200, HP Z210 CMT, HP Z400, and HP xw4000 computers ..... 9
HP xw6200, HP xw6400, and HP xw6600 computers ..... 11
HP Z600 and HP Z800 computers ..... 12
HP xw8000 and HP xw9000 computers ..... 14
Step 3—Installing a hard disk in the DX115 carrier ..... 14
Step 4—Completing the computer assembly ..... 17
Japanese 日本語 ..... 18

CRU Dataport DX115 kit installation

Introduction

This document describes how to install the CRU Dataport DX115® removable media kit in an HP computer. The DX115 kit lets you install removable media in your computer.

Kit contents

Warranty information

DX115 unit (case, drive carrier, SATA power extension cable, screws, and lock key)

Installation document

Two SATA cables

Five M3 screws

One 6-32 screw

Before you begin

To view QuickSpecs and determine the compatibility of this product with your HP computer, see $ \underline{\text{http://www.hp.com/go/productbulletin}} $.

0

399231-007

© 2006–2011 Hewlett-Packard Development Company, L.P. Microsoft, Windows, and Windows Vista are U.S. registered trademarks of Microsoft Corporation. Printed in the U.S.

Warnings and cautions

WARNING! Any surface or area of the equipment marked with this symbol indicates the presence of a hot surface or hot component. If this surface is contacted, the potential for injury exists. To reduce the risk of injury from a hot component, enable the surface to cool before touching.

WARNING! Any surface or area of the equipment marked with this symbol indicates the presence of an electrical shock hazard. To reduce the risk of injury from electrical shock, do not open any enclosed area marked with this symbol.

WARNING! To reduce the risk of electric shock or damage to your equipment:

— Do not disable the power cord grounding plug. The grounding plug is an important safety feature.

— Plug the power cord in a grounded (earthed) outlet that is easily accessible at all times.

— Disconnect power from the equipment by unplugging the power cord from the electrical outlet.

WARNING! To reduce the risk of serious injury, read the Safety & Comfort Guide. It describes proper computer setup, posture, health, and work habits for computer users, and provides important electrical and mechanical safety information. This guide is located at http://www.hp.com/ergo and on the documentation CD (if one is included with the product).

WARNING! If a product is shipped in packaging marked with this symbol, the product must always be lifted by two persons to avoid personal injury due to product weight.

CAUTION: Static electricity can damage the electronic components of the computer. Before beginning these procedures, be sure you discharge static electricity by briefly touching a grounded metal object.

CAUTION: To prevent damage to the computer, observe the following Electrostatic Discharge (ESD) precautions while performing the system parts removal and replacement procedures:

— Work on a static-free mat.

— Wear a static strap to ensure that any accumulated electrostatic charge is discharged from your body to the ground.

— Create a common ground for the equipment you are working on by connecting the static-free mat, static strap, and peripheral units to that piece of equipment.

NOTE: HP accessories are for use in HP computer products. They have been extensively tested for reliability and are manufactured to high quality standards.

Step 1—Preparing for component installation

NOTE: Computer models vary. All illustrations are examples only.

Accessing the internal components of the computer

1. If you need help preparing the computer for this installation, consult the removal and replacement procedures in the service guide for your computer at $ \underline{\text{http://www.hp.com/support/manuals}} $.

2. Power down the computer, and then disconnect the power cord.

3. Power down all external devices, and then disconnect them from the computer.

4. Remove the side access panel.

Step 2—Installing the DX115 case into the optical drive bay

See the steps for the applicable computer model in the following sections.

CAUTION: Insert or remove the carrier (with a disk drive) only when the workstation is shut down. Other procedures may result in system hangs, data loss, or even drive damage. The component supplier's user guide describes a procedure for inserting or removing the carrier (with drive) while the workstation is booted and then powering the drive via the power switch on the enclosure. Microsoft Windows XP and Windows Vista do not support this action.

NOTE: The CRU Dataport DX115 does not fit in all optical drive bays. It is longer than most optical