Aggiusta la tua roba Comunità Store

Rilasciato a luglio 2018, il MacBook Pro da 15", modello A1989, adotta uno schermo retroilluminato a LED da 15,4" con tecnologia True tone, Touch ID e processore fino a esa-core Intel Core i9.

208 Domande Visualizza tutte

Opzioni

Ripped battery connector from logic board

Hey there,

Unfortunately, I ripped the tiny battery connector from the logic board, while trying to take out the battery (picture attached). Is there any way to repair that or do I need to replace the logic board?

Block Image

Update (06/19/23)

Here’s another picture attached. The object (plug?) in the green circle would needed to be placed where the red arrow is pointing to. While trying to take off the cable i ripped it of the logic board.

Block Image

Rispondi a questa domanda Anch'io ho questo problema

Questa è una buona domanda?

Sì No
Punteggio 1
Aggiungi un commento

4 Risposte

Filtra per:
Più utili Più recenti Più Vecchio
Risposta Più Utile

Opzioni

Looks like one solder pad is already missing, thats means you must find in schematic where this line is going and can route a patch line to reconnect it.

When you share the exact motherboard number i can look to schematics.

And good repair shops? Yes, in Wien you can visit me 😄

Questa risposta è stata utile?

Sì No
Punteggio 3

5 Commenti:

Or only model number A**** will be enought to find the line.

da

@vojtech59738 maybe with a closer, clearer picture the trace for the pad may be visible.

da

It's an A1990 model. I will add another picture

da

@nigel yes when is on the 1st Layer, but this MacBook have 7layers PCB.

da

@vojtech59738 on the second picture you can see the trace going to the ripped pad. Doesn’t look like a hard job to fit it. Looking at it you could probably expose part of the trace and run solder from the connector pin to the trace. I did it once with a vape circuit board. Trace was that close to the pin there was no point running a wire.

da

Aggiungi un commento

Opzioni

it can be repaired but it would need someone with good soldering experience to repair it

Questa risposta è stata utile?

Sì No
Punteggio 2

27 Commenti:

Hey @tech_ni & @strongbow,

could you recommend any Repair-Service in Europe/Germany? And, is there any tutorial for the soldering? We have some guys in the company who said they would dare to try by themselves ;)

da

@fen18106 looking at the great bunch of people (excluding myself) that answered you question, I think you already have all the right experts to help you with that repair

da

@fen18106 if your in germany ben or some of the techs at resq would be able to repair it. https://www.resq-repair.com/en. if any of them pads are damaged then you would need the boardview to see where they go and run jumper wires

da

@tech_ni solder a jumper to R6952 :-) boardview verified :-))

da

@oldturkey03 820-00850 board im guessing

da

Mostra altri 22 commenti

Aggiungi un commento

Opzioni

@fen18106 let us know what board number you have on there. I show a 820-01041. That particular pad is SMBUS_3V3_BATT_SCL and could connect directly to R6952.

@strongbow the trace is visible but a PITA top solder too, I'd solder a jumper to the component :-)

Block Image

I am really not sure if the pad is actually off or just needs to be cleaned. Must be my old eyes :-)

Questa risposta è stata utile?

Sì No
Punteggio 2

3 Commenti:

Re-tinning the pads would be a good start then check the path using an Ohm meter or continuity tester between.

Just be careful as you could make things worse.

da

The pad is definitely off - i had it right in my hands ;)

The board number is 820-01041 or 820-01326 - on the box of the MBP "Radeon Pro 560X" is written - and on logi.wiki there is "Radeon ... vega", so I am not 100% sure which one it is: https://logi.wiki/index.php/Board_Number...

da

@fen18106 like I said, maybe my old eyes. Always good to verify. So, the instructions are right and it's the right component to run a jumper to.

da

Aggiungi un commento

Opzioni

Decent computer repair shop should be able to repair that for you. With the correct connector should be easy enough.

Questa risposta è stata utile?

Sì No
Punteggio 1
Aggiungi un commento

Aggiungi la tua risposta

FeN. sarà eternamente grato.
Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 5

Ultimi 30 Giorni: 19

Tutti i Tempi: 287