Salta al contenuto principale
Aiuto

Versione corrente di: Matt Zieminski

Testo:

Hi @eso12
It could be a [product|IF476-422|defrost thermostat|new_window=true] problem or a control board problem.
I included the control board as a possible problem because looking at the [document|32553|tech sheet] for the model the auto defrost cycle occurs after a ''minimum'' ''of 8 hours of compressor run time''. You said that it stops after only ~6 hours. This makes me think that it is not stopping for a defrost cycle. The only other reason that it would normally stop is when the temperatures in the compartment were both at the lower limit of their preset temperature range and therefore no further cooling was required until the temps rose again.
The actual amount of time that the compressor takes to achieve the 8 hours run time may take longer than a straight 8 hours of elapsed time. This depends on such factors as the ambient temp and how many times the doors have been opened due to normal usage e.g. overnight it is cooler and the doors would be opened less often than during the day so less warmer air would have entered the compartments (when the doors were open - or less cooler air lost if you prefer) requiring the compressor to run less often and for shorter periods to cool it back down to the set temps.
Just to eliminate the possibility perhaps check if the temp sensors in both compartments test OK (as per the diagnostics as shown in the tech sheet). The sensors indicate that the correct temp has been reached so the compressor would be turned off. Although it should be turned on again when the temp rises above the upper preset limit.
Looking at the tech sheet the defrost thermostat only opens the defrost heater circuit when (or if) the temp near the evaporator unit exceeds its operating temperature, but in doing this it may also signal the control board to end the defrost cycle. I'm not 100% sure of this but maybe it is worth checking if the defrost thermostat is OK
-Here's a [link|https://www.partselect.com/PS11750673-Whirlpool-WPW10225581-Bi-Metal-Defrost-Thermostat.htm?SourceCode=21&SearchTerm=GSF26C4EXY03&ModelNum=GSF26C4EXY03|link] that shows the location of the defrost thermostat in your model and also has a video that shows how to replace it, that may help.
-
Here's a [link|https://www.youtube.com/watch?v=7kcvlnW8QYo|video] that shows how to correctly test if the defrost thermostat is OK
-The best I can find online states that the defrost thermostat in your refrigerator (part # [link|https://www.ifixit.com/products/whirlpool-refrigerator-defrost-thermostat-wpw10225581|W10225581]) is designed to open at 45°F and to close again at 18°F (to be ready for the next defrost cycle), but as per the test video, check what it shows on the thermostat itself to be sure.
+The best I can find online states that the defrost thermostat in your refrigerator (part # [product|IF476-422|W10225581]) is designed to open at 45°F and to close again at 18°F (to be ready for the next defrost cycle), but as per the test video, check what it shows on the thermostat itself to be sure.
If the thermostat is faulty search online for [product|IF476-422|W10225581|new_window=true] to find suppliers that suit you best.

Stato:

open

Modifica di: Matt Zieminski

Testo:

Hi @eso12
-It could be a [link|https://www.ifixit.com/products/wpw10225581-whirlpool-refrigerator-thermostat|defrost thermostat|new_window=true] problem or a control board problem.
+It could be a [product|IF476-422|defrost thermostat|new_window=true] problem or a control board problem.
I included the control board as a possible problem because looking at the [document|32553|tech sheet] for the model the auto defrost cycle occurs after a ''minimum'' ''of 8 hours of compressor run time''. You said that it stops after only ~6 hours. This makes me think that it is not stopping for a defrost cycle. The only other reason that it would normally stop is when the temperatures in the compartment were both at the lower limit of their preset temperature range and therefore no further cooling was required until the temps rose again.
The actual amount of time that the compressor takes to achieve the 8 hours run time may take longer than a straight 8 hours of elapsed time. This depends on such factors as the ambient temp and how many times the doors have been opened due to normal usage e.g. overnight it is cooler and the doors would be opened less often than during the day so less warmer air would have entered the compartments (when the doors were open - or less cooler air lost if you prefer) requiring the compressor to run less often and for shorter periods to cool it back down to the set temps.
Just to eliminate the possibility perhaps check if the temp sensors in both compartments test OK (as per the diagnostics as shown in the tech sheet). The sensors indicate that the correct temp has been reached so the compressor would be turned off. Although it should be turned on again when the temp rises above the upper preset limit.
Looking at the tech sheet the defrost thermostat only opens the defrost heater circuit when (or if) the temp near the evaporator unit exceeds its operating temperature, but in doing this it may also signal the control board to end the defrost cycle. I'm not 100% sure of this but maybe it is worth checking if the defrost thermostat is OK
Here's a [link|https://www.partselect.com/PS11750673-Whirlpool-WPW10225581-Bi-Metal-Defrost-Thermostat.htm?SourceCode=21&SearchTerm=GSF26C4EXY03&ModelNum=GSF26C4EXY03|link] that shows the location of the defrost thermostat in your model and also has a video that shows how to replace it, that may help.
Here's a [link|https://www.youtube.com/watch?v=7kcvlnW8QYo|video] that shows how to correctly test if the defrost thermostat is OK
-The best I can find online states that the defrost thermostat in your refrigerator (part # W10225581) is designed to open at 45°F and to close again at 18°F (to be ready for the next defrost cycle), but as per the test video, check what it shows on the thermostat itself to be sure.
+The best I can find online states that the defrost thermostat in your refrigerator (part # [link|https://www.ifixit.com/products/whirlpool-refrigerator-defrost-thermostat-wpw10225581|W10225581]) is designed to open at 45°F and to close again at 18°F (to be ready for the next defrost cycle), but as per the test video, check what it shows on the thermostat itself to be sure.
-If the thermostat is faulty search online for [link|https://www.ifixit.com/products/wpw10225581-whirlpool-refrigerator-thermostat|W10225581|new_window=true] to find suppliers that suit you best.
+If the thermostat is faulty search online for [product|IF476-422|W10225581|new_window=true] to find suppliers that suit you best.

Stato:

open

Modifica di: Matt Zieminski

Testo:

Hi @eso12
-It could be a defrost thermostat problem or a control board problem.
+It could be a [link|https://www.ifixit.com/products/wpw10225581-whirlpool-refrigerator-thermostat|defrost thermostat|new_window=true] problem or a control board problem.
I included the control board as a possible problem because looking at the [document|32553|tech sheet] for the model the auto defrost cycle occurs after a ''minimum'' ''of 8 hours of compressor run time''. You said that it stops after only ~6 hours. This makes me think that it is not stopping for a defrost cycle. The only other reason that it would normally stop is when the temperatures in the compartment were both at the lower limit of their preset temperature range and therefore no further cooling was required until the temps rose again.
The actual amount of time that the compressor takes to achieve the 8 hours run time may take longer than a straight 8 hours of elapsed time. This depends on such factors as the ambient temp and how many times the doors have been opened due to normal usage e.g. overnight it is cooler and the doors would be opened less often than during the day so less warmer air would have entered the compartments (when the doors were open - or less cooler air lost if you prefer) requiring the compressor to run less often and for shorter periods to cool it back down to the set temps.
Just to eliminate the possibility perhaps check if the temp sensors in both compartments test OK (as per the diagnostics as shown in the tech sheet). The sensors indicate that the correct temp has been reached so the compressor would be turned off. Although it should be turned on again when the temp rises above the upper preset limit.
Looking at the tech sheet the defrost thermostat only opens the defrost heater circuit when (or if) the temp near the evaporator unit exceeds its operating temperature, but in doing this it may also signal the control board to end the defrost cycle. I'm not 100% sure of this but maybe it is worth checking if the defrost thermostat is OK
Here's a [link|https://www.partselect.com/PS11750673-Whirlpool-WPW10225581-Bi-Metal-Defrost-Thermostat.htm?SourceCode=21&SearchTerm=GSF26C4EXY03&ModelNum=GSF26C4EXY03|link] that shows the location of the defrost thermostat in your model and also has a video that shows how to replace it, that may help.
-Here's a [https://www.youtube.com/watch?v=7kcvlnW8QYo|video] that shows how to correctly test if the defrost thermostat is OK
+Here's a [link|https://www.youtube.com/watch?v=7kcvlnW8QYo|video] that shows how to correctly test if the defrost thermostat is OK
The best I can find online states that the defrost thermostat in your refrigerator (part # W10225581) is designed to open at 45°F and to close again at 18°F (to be ready for the next defrost cycle), but as per the test video, check what it shows on the thermostat itself to be sure.
-If the thermostat is faulty search online for W10225581to find suppliers that suit you best.
+If the thermostat is faulty search online for [link|https://www.ifixit.com/products/wpw10225581-whirlpool-refrigerator-thermostat|W10225581|new_window=true] to find suppliers that suit you best.

Stato:

open

Modifica di: jayeff

Testo:

Hi @eso12
It could be a defrost thermostat problem or a control board problem.
I included the control board as a possible problem because looking at the [document|32553|tech sheet] for the model the auto defrost cycle occurs after a ''minimum'' ''of 8 hours of compressor run time''. You said that it stops after only ~6 hours. This makes me think that it is not stopping for a defrost cycle. The only other reason that it would normally stop is when the temperatures in the compartment were both at the lower limit of their preset temperature range and therefore no further cooling was required until the temps rose again.
The actual amount of time that the compressor takes to achieve the 8 hours run time may take longer than a straight 8 hours of elapsed time. This depends on such factors as the ambient temp and how many times the doors have been opened due to normal usage e.g. overnight it is cooler and the doors would be opened less often than during the day so less warmer air would have entered the compartments (when the doors were open - or less cooler air lost if you prefer) requiring the compressor to run less often and for shorter periods to cool it back down to the set temps.
Just to eliminate the possibility perhaps check if the temp sensors in both compartments test OK (as per the diagnostics as shown in the tech sheet). The sensors indicate that the correct temp has been reached so the compressor would be turned off. Although it should be turned on again when the temp rises above the upper preset limit.
Looking at the tech sheet the defrost thermostat only opens the defrost heater circuit when (or if) the temp near the evaporator unit exceeds its operating temperature, but in doing this it may also signal the control board to end the defrost cycle. I'm not 100% sure of this but maybe it is worth checking if the defrost thermostat is OK
Here's a [link|https://www.partselect.com/PS11750673-Whirlpool-WPW10225581-Bi-Metal-Defrost-Thermostat.htm?SourceCode=21&SearchTerm=GSF26C4EXY03&ModelNum=GSF26C4EXY03|link] that shows the location of the defrost thermostat in your model and also has a video that shows how to replace it, that may help.
-Here's a [https://www.youtube.com/watch?v=7kcvlnW8QYothat shows how to correctly test if the defrost thermostat is OK
+Here's a [https://www.youtube.com/watch?v=7kcvlnW8QYo|video] that shows how to correctly test if the defrost thermostat is OK
The best I can find online states that the defrost thermostat in your refrigerator (part # W10225581) is designed to open at 45°F and to close again at 18°F (to be ready for the next defrost cycle), but as per the test video, check what it shows on the thermostat itself to be sure.
If the thermostat is faulty search online for W10225581to find suppliers that suit you best.

Stato:

open

Modifica di: jayeff

Testo:

Hi @eso12
It could be a defrost thermostat problem or a control board problem.
I included the control board as a possible problem because looking at the [document|32553|tech sheet] for the model the auto defrost cycle occurs after a ''minimum'' ''of 8 hours of compressor run time''. You said that it stops after only ~6 hours. This makes me think that it is not stopping for a defrost cycle. The only other reason that it would normally stop is when the temperatures in the compartment were both at the lower limit of their preset temperature range and therefore no further cooling was required until the temps rose again.
The actual amount of time that the compressor takes to achieve the 8 hours run time may take longer than a straight 8 hours of elapsed time. This depends on such factors as the ambient temp and how many times the doors have been opened due to normal usage e.g. overnight it is cooler and the doors would be opened less often than during the day so less warmer air would have entered the compartments (when the doors were open - or less cooler air lost if you prefer) requiring the compressor to run less often and for shorter periods to cool it back down to the set temps.
Just to eliminate the possibility perhaps check if the temp sensors in both compartments test OK (as per the diagnostics as shown in the tech sheet). The sensors indicate that the correct temp has been reached so the compressor would be turned off. Although it should be turned on again when the temp rises above the upper preset limit.
Looking at the tech sheet the defrost thermostat only opens the defrost heater circuit when (or if) the temp near the evaporator unit exceeds its operating temperature, but in doing this it may also signal the control board to end the defrost cycle. I'm not 100% sure of this but maybe it is worth checking if the defrost thermostat is OK
-Here's a [https://www.partselect.com/PS11750673-Whirlpool-WPW10225581-Bi-Metal-Defrost-Thermostat.htm?SourceCode=21&SearchTerm=GSF26C4EXY03&ModelNum=GSF26C4EXY03|link that shows the location of the defrost thermostat in your model and also has a video that shows how to replace it, that may help.
+Here's a [link|https://www.partselect.com/PS11750673-Whirlpool-WPW10225581-Bi-Metal-Defrost-Thermostat.htm?SourceCode=21&SearchTerm=GSF26C4EXY03&ModelNum=GSF26C4EXY03|link] that shows the location of the defrost thermostat in your model and also has a video that shows how to replace it, that may help.
-Here's a [https://www.youtube.com/watch?v=7kcvlnW8QYo] that shows how to correctly test if the defrost thermostat is OK
+Here's a [https://www.youtube.com/watch?v=7kcvlnW8QYothat shows how to correctly test if the defrost thermostat is OK
The best I can find online states that the defrost thermostat in your refrigerator (part # W10225581) is designed to open at 45°F and to close again at 18°F (to be ready for the next defrost cycle), but as per the test video, check what it shows on the thermostat itself to be sure.
If the thermostat is faulty search online for W10225581to find suppliers that suit you best.

Stato:

open

Post originale di: jayeff

Testo:

Hi @eso12

It could be a defrost thermostat problem or a control board problem.

I included the control board as a possible problem  because looking at the [document|32553|tech sheet] for the model the auto defrost cycle occurs after a ''minimum'' ''of 8 hours of compressor run time''. You said that it stops after only ~6 hours. This makes me think that it is not stopping for a defrost cycle. The only other reason that it would normally stop is when the temperatures in the compartment were both at the lower limit of their preset temperature range and therefore no further cooling was required until the temps rose again.

The actual amount of time that the compressor takes to achieve the 8 hours run time may take longer than a straight 8 hours of elapsed time. This depends on such factors as the ambient temp and how many times the doors have been opened due to normal usage e.g. overnight it is cooler and the doors would be opened less often than during the day so less warmer air would have entered the compartments (when the doors were open - or less cooler air lost if you prefer) requiring the compressor to run less often and for shorter periods to cool it back down to the set temps.

Just to eliminate the possibility perhaps check if the temp sensors in both compartments test OK (as per the diagnostics as shown in the tech sheet). The sensors indicate that the correct temp has been reached so the compressor would be turned off. Although it should be turned on again when the temp rises above the upper preset limit.

Looking at the tech sheet the defrost thermostat only opens the defrost heater circuit when (or if) the temp near the evaporator unit exceeds its operating temperature, but in doing this it may also signal the control board to end the defrost cycle. I'm not 100% sure of this but maybe it is worth checking if the defrost thermostat is OK

Here's a [https://www.partselect.com/PS11750673-Whirlpool-WPW10225581-Bi-Metal-Defrost-Thermostat.htm?SourceCode=21&SearchTerm=GSF26C4EXY03&ModelNum=GSF26C4EXY03|link that shows the location of the defrost thermostat in your model and also has a video that shows how to replace it, that may help.

Here's a [https://www.youtube.com/watch?v=7kcvlnW8QYo] that shows how to correctly test if the defrost thermostat is OK

The best I can find online states that the defrost thermostat in your refrigerator (part # W10225581) is designed to open at 45°F and to close again at 18°F (to be ready for the next defrost cycle), but as per the test video, check what it shows on the thermostat itself to be sure.

If the thermostat is faulty search online for W10225581to find suppliers that suit you best.

Stato:

open