Aggiusta la tua roba Comunità Store

OontZ Angle 3 Speaker Replacement

Introduzione

In this guide, some soldering is required when disconnecting the speakers from the motherboard. If you are unfamiliar with soldering, watch Soldering Tutorial for Beginners, Five Easy Steps to familiarize yourself and to be able to correctly replace the speakers.

Cosa ti serve

  1. OontZ Angle 3 Speaker Replacement, Back Case: passo 1, immagine 1 di 3 OontZ Angle 3 Speaker Replacement, Back Case: passo 1, immagine 2 di 3 OontZ Angle 3 Speaker Replacement, Back Case: passo 1, immagine 3 di 3

    • Make sure that the OontZ Angle 3 is powered off before starting the disassembly.

    • Use the plastic opening tool to remove the rubber caps from each end of the speaker.

    Traduci

  2. OontZ Angle 3 Speaker Replacement: passo 2, immagine 1 di 1

    • Remove four (4) 11.7 mm Phillips #0 screws from each side at the bottom of the speaker.

    Traduci

  4. OontZ Angle 3 Speaker Replacement: passo 3, immagine 1 di 2 OontZ Angle 3 Speaker Replacement: passo 3, immagine 2 di 2

    • Use the plastic opening tool on one of the corners to separate the bottom piece from the speaker, and then remove the piece.

    Traduci

  5. OontZ Angle 3 Speaker Replacement, Speaker: passo 4, immagine 1 di 2 OontZ Angle 3 Speaker Replacement, Speaker: passo 4, immagine 2 di 2

    • Use the plastic opening tool to remove the front speaker plate from the speaker.

    Traduci

  6. OontZ Angle 3 Speaker Replacement: passo 5, immagine 1 di 2 OontZ Angle 3 Speaker Replacement: passo 5, immagine 2 di 2

    • Remove the eight (8) 5.25mm screws with the Phillips #0 screwdriver.

    • Open access to the speakers by letting them rest as shown.

    Traduci

  7. OontZ Angle 3 Speaker Replacement: passo 6, immagine 1 di 2 OontZ Angle 3 Speaker Replacement: passo 6, immagine 2 di 2

    • Use the soldering iron to carefully disconnect the speaker(s) from the motherboard connection wires.

    • Learn more about soldering here.

    • Remove the disconnected speaker(s).

    • When reconnecting the wires to the new speaker(s), be careful to connect the wires to the correct nodes (red for positive and black for negative). If they are reconnected to the wrong locations the speakers will either not work or break.

    Traduci
Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 10 persone hanno completato questa guida.

Autore

con 1 altro collaboratore

Mason Hollander

Membro da: 01/20/16

1.387 Reputazione

4 Guide realizzate

Distintivi: 15

+12 altri distintivi

Team

USF Tampa, Team 15-6, Remmell Spring 2016 Membro di USF Tampa, Team 15-6, Remmell Spring 2016

USFT-REMMELL-S16S15G6

4 Membri

4 Guide realizzate

7 Commenti

Where do you buy replacement speakers?

michalfiona - Replica

Where do you buy the replacement speakers?

What type to buy?

michalfiona - Replica

where i buy the speaker replacement/

Sharina Uadan - Replica

Where can i buy the replacement speakers

Anil Meda - Replica

same question, I am looking for original speaker for oontz angle 3 and I can’t find one. Those who are looking for the size, its 40x40mm (1.57”) 4ohms 3W

Dwayne Champ Manuel - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 4

Ultimi 7 Giorni: 22

Ultimi 30 Giorni: 74

Tutti i Tempi: 8,071