Introduzione

A guide on how to remove the Fan.

Turn the laptop bottom side up with the rear panel facing forward.
  • Turn the laptop bottom side up with the rear panel facing forward.

Aggiungi Commento

Remove the two T8 Torx screws that secure the LED cover to the base enclosure.
  • Remove the two T8 Torx screws that secure the LED cover to the base enclosure.

Aggiungi Commento

Turn the laptop top side up with the front facing forward. Open the screen.
  • Turn the laptop top side up with the front facing forward. Open the screen.

Aggiungi Commento

Locate the F1 and F2 keys near the top left corner of the keyboard.
  • Locate the F1 and F2 keys near the top left corner of the keyboard.

Aggiungi Commento

While holding the F1 and F2 keys, insert a spudger between the keys into the notch in the LED cover. Lift up.
  • While holding the F1 and F2 keys, insert a spudger between the keys into the notch in the LED cover. Lift up.

Aggiungi Commento

Locate the Pause and Scroll keys near the top right corner of the keyboard.
  • Locate the Pause and Scroll keys near the top right corner of the keyboard.

Aggiungi Commento

While holding the Pause and Scroll keys, insert a spudger between the keys into the notch in the LED cover. Lift up.
  • While holding the Pause and Scroll keys, insert a spudger between the keys into the notch in the LED cover. Lift up.

Aggiungi Commento

Insert a spudger between the F7 and F8 keys. Lift up to remove the LED cover. Insert a spudger between the F7 and F8 keys. Lift up to remove the LED cover.
  • Insert a spudger between the F7 and F8 keys. Lift up to remove the LED cover.

Aggiungi Commento

Lift the back edge of the keyboard and pull towards the screen.
  • Lift the back edge of the keyboard and pull towards the screen.

Aggiungi Commento

Pull the cable and lift up to release.
  • Pull the cable and lift up to release.

Aggiungi Commento

Kit RAM Mac
Accelera il Mac. Porta la memoria al massimo.
Kit RAM Mac
Metti più memoria nel tuo Mac.
Remove the keyboard.
  • Remove the keyboard.

Aggiungi Commento

Locate the fan near the top left corner. It has three colored wires: yellow, red, and black.
  • Locate the fan near the top left corner. It has three colored wires: yellow, red, and black.

  • Disconnect the cable connecting the fan to the system board.

Aggiungi Commento

Locate and remove the four screws in the copper plate.
  • Locate and remove the four screws in the copper plate.

Aggiungi Commento

Remove the heat spreader by pulling the whole assembly up out of the computer.
  • Remove the heat spreader by pulling the whole assembly up out of the computer.

Aggiungi Commento

Flip the computer bottom side up with the rear facing forward.
  • Flip the computer bottom side up with the rear facing forward.

Aggiungi Commento

Remove the six screws shown in picture.
  • Remove the six screws shown in picture.

Aggiungi Commento

Remove battery and then remove screw in  metal support on case edge
  • Remove battery and then remove screw in metal support on case edge

  • Flip the computer top side up with the front facing you.

Aggiungi Commento

Lift up the palm rest from the front edge and swing it towards the screen.
  • Lift up the palm rest from the front edge and swing it towards the screen.

Aggiungi Commento

Locate the first connector. Disconnect by firmly pulling up.
  • Locate the first connector. Disconnect by firmly pulling up.

Aggiungi Commento

Locate the second connector. Remove by firmly pulling up.
  • Locate the second connector. Remove by firmly pulling up.

Aggiungi Commento

Remove the palm rest.
  • Remove the palm rest.

Aggiungi Commento

Turn the base bottom side up.
  • Turn the base bottom side up.

Aggiungi Commento

Remove the two TM 2.5mm x 8.0mm screws that secure the top cover to the base.
  • Remove the two TM 2.5mm x 8.0mm screws that secure the top cover to the base.

Aggiungi Commento

Turn the base top side up with the front facing forward.
  • Turn the base top side up with the front facing forward.

Aggiungi Commento

Remove the three TM 2.5 mm x 5.0 mm screws that secure the top cover to the base.
  • Remove the three TM 2.5 mm x 5.0 mm screws that secure the top cover to the base.

Aggiungi Commento

Lift the top cover straight up about one inch, then slide forward until the microphone cable is exposed.
  • Lift the top cover straight up about one inch, then slide forward until the microphone cable is exposed.

  • Disconnect the microphone cable from the system board.

Aggiungi Commento

Remove the top cover from the base.
  • Remove the top cover from the base.

Aggiungi Commento

Disconnect the fan cable from the system board.
  • Disconnect the fan cable from the system board.

Aggiungi Commento

Remove the fan from the base.
  • Remove the fan from the base.

Aggiungi Commento

Conclusione

To reassemble your device, follow these instructions in reverse order.

Alex Hernandez

Membro da: 14/04/2010

28 Reputazione

4 Guide realizzate

Team

Cal Poly, Team 29-74, Johann Spring 2010 Membro di Cal Poly, Team 29-74, Johann Spring 2010

CPSU-JOHANN-S10S29G74

3 Membri

7 Guide realizzate

Remove battery FIRST before you do anything. Then remove all the screws on the back of the computer. The you can go to the front and follow all the steps afterward.

iam765 - Replica

Please DO NOT firmly remove any connectors. Most connectors have locks. In step 20 you can see the two different colors of the connector the bottom is black and the top (the lock) is brown. Each side of the lock sticks out further than the connector. One side at a time pull back on the lock. Connection should come out with no force. to reconnect, seat connection and push lock back in place. If any issues try unlocking and re-seat connection.

iam765 - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 1

Ultimi 7 Giorni: 1

Ultimi 30 Giorni: 4

Tutti i Tempi: 5,411