Salta al contenuto principale

Aggiusta la tua roba

Diritto alla Riparazione

Store

Avviso: Stai modificando una guida prerequisita. Tutte le modifiche avranno effetto su tutte le guide che includono questo passo.

Inglese
Italiano

Traduzione in corso passo 2

Passo 2
This is a good time to power on your iPad and test all functions before you seal the display in place. Be sure to power your iPad back down completely before you continue. If you're installing a new front panel assembly, it may need the following preparation:
Front panel preparation
  • This is a good time to power on your iPad and test all functions before you seal the display in place. Be sure to power your iPad back down completely before you continue.

  • If you're installing a new front panel assembly, it may need the following preparation:

  • Peel the large clear plastic liner off of the inside of the glass.

  • Peel any blue plastic backings covering the adhesive around the perimeter of the front panel assembly.

  • Once removed, the adhesive strips will be exposed. Don't remove these backings until you're ready to install the front panel assembly.

  • Don't remove any copper coverings from the outlined region, such as yellow kapton tape or black electrical tape.

  • Ensure the glass panel is free of fingerprints and grime before installing it on your device.

Se stai installando un nuovo gruppo del pannello anteriore, potresti dover fare i seeguenti preparativi:

Rimuovi le coperture in plastica dell'adesivo attorno al perimetro del gruppo del pannello anteriore.

Rimuovi il piccolo pezzo di adesivo protettivo dal cavo del digitizer.

Assicurati che tutto il rame sia coperto sul nuovo schermo di ricambio, altrimenti, una volta installato in questo modo, potrebbe muoversi in modo casuale.

[*title] Front panel preparation
[* icon_reminder] This is a good time to power on your iPad and test all functions before you seal the display in place. Be sure to power your iPad back down completely before you continue.
[*
icon_note] If you're installing a new front panel assembly, it may'''may''' need the following preparation:
[* red] Peel the large clear plastic stripsliner off of the inside of the glass.
[* orange] Peel any blue plastic backings
covering the adhesive around the perimeter of the front panel assembly.
[* orange] Remove

[* icon_caution] Once removed,
the small piece of adhesive backingstrips will be exposed. Don't remove these backings until you're ready to install the front panel assembly.
[* yellow] '''Don't remove any copper coverings
from the digitizer cableoutlined region''', such as yellow kapton tape or black electrical tape.
[* black] Make sure all copperEnsure the glass panel is coveredfree of fingerprints and grime before installing it on the new replacement screen as once fitted without this the screen will move randomlyyour device.
[*title] Front panel preparation
[* icon_reminder] This is a good time to power on your iPad and test all functions before you seal the display in place. Be sure to power your iPad back down completely before you continue.
[*
icon_note] If you're installing a new front panel assembly, it may'''may''' need the following preparation:
[* red] Peel the large clear plastic stripsliner off of the inside of the glass.
[* orange] Peel any blue plastic backings
covering the adhesive around the perimeter of the front panel assembly.
[* orange] Remove

[* icon_caution] Once removed,
the small piece of adhesive backingstrips will be exposed. Don't remove these backings until you're ready to install the front panel assembly.
[* yellow] '''Don't remove any copper coverings
from the digitizer cableoutlined region''', such as yellow kapton tape or black electrical tape.
[* black] Make sure all copperEnsure the glass panel is coveredfree of fingerprints and grime before installing it on the new replacement screen as once fitted without this the screen will move randomlyyour device.

I tuoi contributi sono usati su licenza in base alla licenza open source Creative Commons.