Questa versione può contenere modifiche errate. Passa all'ultima istantanea verificata.
Cosa ti serve
-
-
Spegni il tuo iPhone prima di iniziare lo smontaggio.
-
La cover posteriore del telefono potrebbe avere due viti a croce Phillips #000 o viti "Pentalobe" a 5 punte di Apple. Controlla quali viti hai e assicurati di avere anche il cacciavite corretto per rimuoverle.
-
Rimuovi le due viti Pentalobe o Phillips #000 da 3,6 mm accanto al connettore dock.
-
-
-
Rimuovi la singola vite a croce Philips da 1,5 mm che fissa il connettore della batteria alla scheda madre (se presente).
-
-
-
Solleva la linguetta di plastica trasparente esposta per staccare la batteria dall'adesivo che la fissa all'iPhone.
-
Se è rimasta della soluzione alcolica nel telefono, puliscilo con cura o lascialo asciugare all'aria prima di installare la nuova batteria.
-
Rimuovi la batteria.
-
Prima del riassemblaggio, pulisci i punti di contatto metallo su metallo con uno sgrassante come windex. Gli oli delle dita possono potenzialmente causare problemi di interferenza wireless.
-
Esegui un hard reset dopo il rimontaggio. Ciò può prevenire diversi problemi e semplificare la risoluzione dei problemi.
-
-
-
Rimuovi le due viti a croce Phillips da 1,8 mm che fissano il cavo del connettore dock alla scheda logica.
-
Rimuovi la sottile copertura del cavo del connettore dock in metallo.
-
-
-
-
Rimuovi le seguenti cinque viti:
-
Tre viti a croce Phillips da 1,3 mm
-
Una vite a croce Phillips da 1,5 mm
-
Una vite a croce Phillips da 2,4 mm
-
-
-
Scollega i cinque cavi vicino alla parte superiore della scheda logica nel seguente ordine:
-
Cavo jack per cuffie/pulsante del volume
-
Cavo del pulsante di accensione
-
Cavo della fotocamera frontale
-
Cavo digitalizzatore
-
Cavo dati display
-
Per scollegare i cavi, usa il bordo di uno strumento di apertura in plastica per sollevare delicatamente i connettori verso l'alto e fuori dalle prese sulla scheda logica.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the edge of a plastic opening tool to peel the earpiece speaker off the foam adhesive securing it to the iPhone.
-
Remove the earpiece speaker.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the two 2.0 mm Phillips screws securing the power button bracket to the outer case.
-
Slightly pull the power button cable bracket away from the outer case.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the edge of a plastic opening tool to gently pry up the bracket above the void where the earpiece speaker was installed.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a plastic opening tool to gently peel up the power button cable from the outer case.
-
Remove the power button cable from the iPhone.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a plastic opening tool to remove the metal power button bracket from the power button switch.
-
Annulla: non ho completato questa guida.
Altre 84 persone hanno completato questa guida.
3 Commenti
My power button quit working. I bought the cable assembly and replaced it per these instructions. Everything seemed to work at first but later I noticed my phone kept trying to shut itself off. Any ideas what is causing this? It only seems to occur after I use the power button. It is almost as if it is getting stuck down.
Please remove your screen first, before replacing power button or sensor cable. I advise you to not dare attempt to remove those Step 25 screws (power button cable bracket ) while screen is mounted.
It is too risky! Display's ribbon cable interferes with driver access to these screws. While driving these screws, I unknowingly broke my display cable. It is actually a delicate circuit, not just a simple flexible ribbon. If I knew just how delicate is display cable, then I would not have ventured to perform this replacement. (In my case, only proximity sensor was not working; power and and ambient light sensor were both functioning. In my case, it was not worth breaking a pricy screen for sake of a cheap sensor.)
With a broken screen cable, iPhone endlessly repeats a diagnostic sound or vibration.
iPhone endlessly repeats the "power supply accepted" sound or vibration