Aggiusta le tue cose Community Store

Zoomer Dino Boomer Main Circuit Board Replacement

Introduzione

This guide shows how to safely separate the main circuit board from the remainder of Zoomer Dino Boomer so that it can be replaced without damage to the electrical system.

Cosa ti serve

  1. Zoomer Dino Boomer Main Circuit Board Replacement, Back Cover: passo 1, immagine 1 di 1

    • Power off Zoomer Dino Boomer before disassembly.

    • Remove the eight 9.3mm Phillips #1 screws.

    Modifica

  2. Zoomer Dino Boomer Main Circuit Board Replacement: passo 2, immagine 1 di 2 Zoomer Dino Boomer Main Circuit Board Replacement: passo 2, immagine 2 di 2

    • Turn dinosaur over and hold upright.

    • Use the spudger to pry apart the back cover from the remainder of the Zoomer Dino Boomer.

    • Be gentle while removing the back cover. The back cover of the Zoomer Dino Boomer is still connected to the electronic system by a wire.

    Modifica

  3. Zoomer Dino Boomer Main Circuit Board Replacement: passo 3, immagine 1 di 3 Zoomer Dino Boomer Main Circuit Board Replacement: passo 3, immagine 2 di 3 Zoomer Dino Boomer Main Circuit Board Replacement: passo 3, immagine 3 di 3
    Attrezzo utilizzato in questo passaggio:
    Tweezers
    $4.99
    Acquista

    • Disconnect the wire that connects the back cover of the dino to the main circuit board by carefully pulling on the orange wire connector with tweezers.

    • Remove back cover.

    • If you are having difficulty removing the connector from its socket, push in the small tabs on the side of the connector with the tweezers. This step may take some work.

    • Do not damage the wires or circuit board.

    Modifica

  5. Zoomer Dino Boomer Main Circuit Board Replacement, Main Circuit Board: passo 4, immagine 1 di 3 Zoomer Dino Boomer Main Circuit Board Replacement, Main Circuit Board: passo 4, immagine 2 di 3 Zoomer Dino Boomer Main Circuit Board Replacement, Main Circuit Board: passo 4, immagine 3 di 3
    Attrezzo utilizzato in questo passaggio:
    Tweezers
    $4.99
    Acquista

    • Use tweezers to remove all of the colored wire connectors from their sockets on the circuit board.

    Modifica

  6. Zoomer Dino Boomer Main Circuit Board Replacement: passo 5, immagine 1 di 2 Zoomer Dino Boomer Main Circuit Board Replacement: passo 5, immagine 2 di 2

    • Remove legs.

    Modifica

  7. Zoomer Dino Boomer Main Circuit Board Replacement: passo 6, immagine 1 di 1

    • Remove the three 7.2 mm Phillips #0 screws connecting the main circuit board to the body of Zoomer Dino Boomer.

    Modifica

  8. Zoomer Dino Boomer Main Circuit Board Replacement: passo 7, immagine 1 di 3 Zoomer Dino Boomer Main Circuit Board Replacement: passo 7, immagine 2 di 3 Zoomer Dino Boomer Main Circuit Board Replacement: passo 7, immagine 3 di 3

    • Use soldering iron and tweezers to disconnect main circuit board from the black and red wires.

    • Check out iFixit's soldering techniques guide to learn more about soldering and desoldering connections.

    • Remove main circuit board from Zoomer Dino Boomer

    Modifica
Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 5 persone hanno completato questa guida.

Autore

con 4 altri collaboratori

Desiree DesJardins

Membro da: 09/02/15

452 Reputazione

2 Guide realizzate

Distintivi: 14

+11 altri distintivi

Team

USF Tampa, Team 16-1, Wollert Fall 2015 Membro di USF Tampa, Team 16-1, Wollert Fall 2015

USFT-WOLLERT-F15S16G1

3 Membri

10 Guide realizzate

4Commenti sulla guida

can anyone tell me where to get a replacement motherboard?

alan.scott - Replica

Nah cuz my dino doesn't show any life support at all just the controller and Idek what's the issue. If this is the way to solve it be so for real tell me where to get that new circuit.

Nightmare_Requiem - Replica

The batteries location?

Tony Beatenbo - Replica

Is there a way to look at the dinosaurs code?
In other words, how it runs?
I´m having one for 5 years now and would like to create a digital copy.
It´s a private project and i alrerady finished the 3D Model.
If you know anything about this topic or someone familiar with that, please reply.
Thank you in advance

Blend Craft - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 2

Ultimi 7 Giorni: 9

Ultimi 30 Giorni: 28

Tutti i Tempi: 4,696