Salta al contenuto principale

Aggiusta la tua roba

Diritto alla Riparazione

Store

Introduzione

The Joysticks on your Xbox Controller could become unresponsive or sticky. If this happens it could be necessary to remove the Joysticks to either replace or clean them. This guide will teach you how to access and replace the Joysticks on your Xbox One Wireless Controller Model 1708.

  1. Slide the battery cover toward the top of the controller to remove it. Lift up  the batteries or the battery pack from the battery compartment.
    • Slide the battery cover toward the top of the controller to remove it.

    • Lift up the batteries or the battery pack from the battery compartment.

  2. Insert a plastic opening tool into the top seam, and  gently work the opening tool to the bottom of the controller. Continue using the opening tool to gently pry the side plate off of the controller.
    • Insert a plastic opening tool into the top seam, and gently work the opening tool to the bottom of the controller.

    • Continue using the opening tool to gently pry the side plate off of the controller.

    • Repeat this process for the second side plate.

    Only use a pry tool! The vibration motor wires are exposed and directly accessible from the side when opening. I attempted to open it with a small knife, expecting to be able to gently pry the clips open, accidentally sliced through my right motor’s wires.

    Sawyer Coe - Replica

    Not a sharp of course.

    Kajus Slekys -

  3. SKIP THE UPGRADE

    Save by fixing with an all-in-one kit.

    Shop iPhone Fix Kits

    SKIP THE UPGRADE

    Save by fixing with an all-in-one kit.

    Shop iPhone Fix Kits
  4. Gently peel the battery label  or punch a hole in the center of the sticker in the battery compartment to reveal the hidden screw.
    • Gently peel the battery label or punch a hole in the center of the sticker in the battery compartment to reveal the hidden screw.

    • Remove the five 9mm torx-9 security screws from the back of the controller.

    Torx-8 security bits work as well.

    jahiamir - Replica

    Torx 8 or 9 wasn’t working. I used 2.0 minus screwdriver

    richjlee - Replica

    The 2.0 minus worked for me as well.

    metric - Replica

  5. Orient the controller so the front plate is facing up. Lift the front cover off of the controller.
    • Orient the controller so the front plate is facing up.

    • Lift the front cover off of the controller.

  6. Turn the controller face down and gently lift the rear plate.
    • Turn the controller face down and gently lift the rear plate.

    Reassembly: When placing the back cover on: notice that the battery terminals need to slide inside the cover first. Then compress the triggers slightly, Then the cover will be aligned correctly. Then add the front cover and add screws so it doesn’t come undone.

    hunteil - Replica

  7. Pull the joysticks off of the controller.
    • Pull the joysticks off of the controller.

    Are the joystick potentiometers soldered to the mother board or just push fit, this guide doesn’t mention soldering so I’m assuming the latter?

    Can you get genuine replacement joystick potentiometers as I’ve only seen cheap eBay type ones?

    Alan - Replica

Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 84 persone hanno completato questa guida.

Dylan Gross

Membro da: 25/09/2017

3.518 Reputazione

4 Guide realizzate

Team

Cal Poly, Team S18-G3, Forte Fall 2017 Membro di Cal Poly, Team S18-G3, Forte Fall 2017

CPSU-FORTE-F17S18G3

4 Membri

7 Guide realizzate

How about the square thing with the stick and hinges that the joystick is attached to? I think it’s called the Module. I have a joystick drift / drifting problem and that may help me out. Thanks.

Cory C - Replica

Agreed. That’s actually the part I need to replace too. The module.

Thomas Tomchak -

followed this guide to take the controller apart because I had a joystick that was sticking, my solution was to put some 3in1 oil on the module that was sticking and it seems to be working a lot better now.

John Jaggi - Replica

@corytc and @tomchak I did replace the module, in general, you buy (Amazon or eBay) you will receive a module of 6 modules you need a multimeter and test each module interface, measure both resistances and subtract them, the one nearest zero is the module you will use since is the one with least drift from the factory.

Just disassemble it, turn upside down uses a solder remover and unsolder the old one, place the new one solder back, boom you are done.

Like you will need an iron solder with medium and thin tips, I used lead-free solder, so is a patience test, be careful with the wires from the rumbles, try not to unsolder them since is a thin wire and is difficult, like I have big hands so took me a while to solder back.

Luis Vitorio Cargnini - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 28

Ultimi 7 Giorni: 148

Ultimi 30 Giorni: 767

Tutti i Tempi: 23,395