Salta al contenuto principale

Cosa ti serve

Questo smontaggio non è una guida di riparazione. Per riparare il tuo Whelen Slimlighter Super-LED, usa il nostro manuale di assistenza.

  1. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 1, immagine 1 di 2 : passo 1, immagine 2 di 2
    • This is Whelen's second generation Slimlighter. Whilst the first generation had multiple 5mm LED's, this generation Slimlighter has 'only' 12 TIR6 style LED's.

    • Enough chatter, let's take it apart :)

  2. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 2, immagine 1 di 3 : passo 2, immagine 2 di 3 : passo 2, immagine 3 di 3
    • Optionally one can first take of the suctioncup brackets. They are held in place by two Philips screws.

    • Next you can take off the retaining brackets. They are held back by a little notch that has to be lifted with a spudger. Repeat this step for the other side.

    • Once the notch is lifted pull the bracket away from the light as shown.

  3. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 3, immagine 1 di 3 : passo 3, immagine 2 di 3 : passo 3, immagine 3 di 3
    • Once the brackets are released the light can easily be dissasembled. Begin by lifting the diffuser lens up as shown.

    • One can also have clear lenses here, the procedure is the same.

    • Note that the lens has a similar notch on the other side, underneath the Whelen logo. Carefully pull the lens out from underneath, don't force anything or it will break.

  4. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 4, immagine 1 di 3 : passo 4, immagine 2 di 3 : passo 4, immagine 3 di 3
    • With the diffuser lenses removed the optics are exposed. They are not secured by anything so carefulle take them out as shown

    • Nifty little optics here, kudo's to Whelen.

    • Try activating the light now, see the differences with and without these optics

  5. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 5, immagine 1 di 3 : passo 5, immagine 2 di 3 : passo 5, immagine 3 di 3
    • Now you can CAREFULLY take out the LED assembly. It's attached to a metal heat dissapating bracket. CAREFUL with the wiring. Note that the bracket is retained by the plastic housing. It might need some help before it gives way.

  6. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 6, immagine 1 di 3 : passo 6, immagine 2 di 3 : passo 6, immagine 3 di 3
    • The wires are held back /retained by a stickon Whelen logo. The logo can easily be removed, just tear it off carefully.

  7. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 7, immagine 1 di 3 : passo 7, immagine 2 di 3 : passo 7, immagine 3 di 3
    • Once the Whelen logo tab is removed the light comes apart completley.

    • Take out the two metal brackets holding the light.

    • Note that one of the brackets holds (part of) the flasher assembly.

  8. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 8, immagine 1 di 3 : passo 8, immagine 2 di 3 : passo 8, immagine 3 di 3
    • If desired, take out the six Philips screws to remove the LED circuit board from the bracket.

    • Note that the rear circuit board is held back by the same screws.

    • The LED board can easily be replaced by any other TIR6 board, any color (as far as I could check!)

    • Note that there is cooling paste between the LED board and the bracket. Make sure you replace it.

  9. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 9, immagine 1 di 2 : passo 9, immagine 2 di 2
    • All done! No more steps required :)

V3nture

Membro da: 10/22/10

161 Reputazione

1 Guida realizzata

0 Commenti

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 2

Ultimi 7 Giorni: 9

Ultimi 30 Giorni: 28

Tutti i Tempi: 7,587