Salta al contenuto principale

Introduzione

This Audio System is the model SRS-XB30. One of the common malfunctions is the charging port. This guide will show you step by step instructions on how to replace the charging port.

  1. To remove the speaker grill, insert the big spudger underneath it in each corner.
    • To remove the speaker grill, insert the big spudger underneath it in each corner.

    • Work around the edges to pry the grill up and off.

  2. With the Sony logo facing towards you, use the medium spudger to lift the side plates from the internal frame. This will need to be done on all four sides of the speaker to remove all four panels
    • With the Sony logo facing towards you, use the medium spudger to lift the side plates from the internal frame.

    • This will need to be done on all four sides of the speaker to remove all four panels

    • This requires some effort because the adhesive is sticky.

  3. Locate the four screws on the now exposed front panel. Using the screwdriver with bit T7, unscrew each screw (15.0 mm long).
    • Locate the four screws on the now exposed front panel.

    • Using the screwdriver with bit T7, unscrew each screw (15.0 mm long).

  4. Next, remove the four outer edge screws, located on each corner of the speaker. The outer edge of the speaker is a clear plastic.
    • Next, remove the four outer edge screws, located on each corner of the speaker. The outer edge of the speaker is a clear plastic.

    • Use the same T7 screwdriver head here.

    • Remove each of the four corner screws (15.0 mm long).

  5. With a little force, carefully lift the lid of the speaker.
    • With a little force, carefully lift the lid of the speaker.

    • Make sure that you do not pull on the wires.

  6. Unclip the four wire connectors (that are attached to the speaker lid). Unclip the four wire connectors (that are attached to the speaker lid). Unclip the four wire connectors (that are attached to the speaker lid).
    • Unclip the four wire connectors (that are attached to the speaker lid).

  7. Kit riparazione batterie MacBook

    A partire da $69.99

    Buy Now

    Kit riparazione batterie MacBook

    A partire da $69.99

    Buy Now
  8. Separate the speaker lid from the bottom frame.
    • Separate the speaker lid from the bottom frame.

    • To prepare the speaker for the next step place the lid parallel to the frame.

  9. Locate the two silver screws (9 mm) attached to the two LED-light-chips on the speaker lid.
    • Locate the two silver screws (9 mm) attached to the two LED-light-chips on the speaker lid.

    • Using the screwdriver with bit PH1, unscrew each screw.

  10. Separate the speaker lid entirely from the bottom frame.
    • Separate the speaker lid entirely from the bottom frame.

  11. Remove the top screw (10 mm).
    • Remove the top screw (10 mm).

    • Use the screwdriver with bit T7.

  12. Locate and remove the three black screws (10.0 mm) within the internal frame. Use bit T7. There are two screws on the left side of the white box and one to its right.
    • Locate and remove the three black screws (10.0 mm) within the internal frame. Use bit T7.

    • There are two screws on the left side of the white box and one to its right.

  13. Slightly lift the white box with all the wires still attached.
    • Slightly lift the white box with all the wires still attached.

  14. Take the big spudger and pry the black casing up from the circuit box. Take the big spudger and pry the black casing up from the circuit box.
    • Take the big spudger and pry the black casing up from the circuit box.

  15. Locate the blue film attached to the circuit box containing the charging port.
    • Locate the blue film attached to the circuit box containing the charging port.

    • Detach the blue film from the box.

  16. Detach the yellow, black and red wires by pulling them directly up.
    • Detach the yellow, black and red wires by pulling them directly up.

  17. Insert the spudger along the battery edge and firmly hold the wires. Lift both sides up. The battery will pop out from its encasement. Insert the spudger along the battery edge and firmly hold the wires. Lift both sides up. The battery will pop out from its encasement.
    • Insert the spudger along the battery edge and firmly hold the wires. Lift both sides up. The battery will pop out from its encasement.

  18. Locate the circuit box containing the yellow charging port.
    • Locate the circuit box containing the yellow charging port.

    • Remove the circuit box from any attachments connecting it to the speaker.

  19. Insert a new circuit box.
    • Insert a new circuit box.

Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 2 persone hanno completato questa guida.

Hi where I can find new circuit box?

cesar2_realmadrid - Replica

YEAH - WERE DO YOU GET A REPLACEMENT?

Cheers

Tim

Tim Terry - Replica

That’s right , at the very beginning it says that no parts are needed , what about the new charging port where can we get it?

Julio aguilar 44 - Replica

I am incredibly curious, and a little bit excited, to hear what it is that was going through your mind at the start of this in comparison to when you reached the end? The exact moment that the very title of this article says very clearly the word “replacement” and then to see the amazing luck of the mistaken omission which read “No Parts Required” only to then be let down again when you realized that a part was in fact required. After-all it is called “Charging Port Replacement” so I’m sure you probably healed up pretty quick from the heartbreak you suffered.

John Wick -

Very clear instructions, thanks.

Any idea where I can find a new charging port for my speaker? Can’t find anything on the internet..

Thanks by advance

Dries

driesdebrauwer123 - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 3

Ultimi 7 Giorni: 27

Ultimi 30 Giorni: 181

Tutti i Tempi: 2,843