Aggiusta la tua roba Comunità Store

Shark Flex DuoClean LED Headlight Replacement

Introduzione

You may need to replace the LED lights if they do not flash when the device is turned on. To remove the motor, soldering skills are required. See this guide for soldering instructions.

Cosa ti serve

  1. Shark Flex DuoClean LED Headlight Replacement, Garage Door: passo 1, immagine 1 di 2 Shark Flex DuoClean LED Headlight Replacement, Garage Door: passo 1, immagine 2 di 2

    • Open the garage door by sliding both of the release buttons away from you.

    • Lift off the garage door.

    Modifica

  2. Shark Flex DuoClean LED Headlight Replacement, Side Component: passo 2, immagine 1 di 2 Shark Flex DuoClean LED Headlight Replacement, Side Component: passo 2, immagine 2 di 2

    • Remove the plastic screw covering using a metal spudger by pushing the sharp side into the crevice and prying the cover out.

    Modifica

  3. Shark Flex DuoClean LED Headlight Replacement: passo 3, immagine 1 di 2 Shark Flex DuoClean LED Headlight Replacement: passo 3, immagine 2 di 2

    • Turn the T10 Security Torx screwdriver counterclockwise to remove the 15mm screw.

    Modifica

  4. Shark Flex DuoClean LED Headlight Replacement: passo 4, immagine 1 di 1

    • Use the iFixit Opening Tool to pry the side of the vacuum open.

    Modifica

  6. Shark Flex DuoClean LED Headlight Replacement: passo 5, immagine 1 di 1

    • Remove the side component with your hands.

    Modifica

  7. Shark Flex DuoClean LED Headlight Replacement, LED Headlight: passo 6, immagine 1 di 1

    • Turn the T10 Security Torx screwdriver counterclockwise to remove the 15mm screw.

    Modifica

  8. Shark Flex DuoClean LED Headlight Replacement: passo 7, immagine 1 di 2 Shark Flex DuoClean LED Headlight Replacement: passo 7, immagine 2 di 2

    • Use the nylon spudger to pry the gold, plastic cover off of the headlights.

    • Prying off the cover too aggressively may cause it to break.

    Modifica

  9. Shark Flex DuoClean LED Headlight Replacement: passo 8, immagine 1 di 2 Shark Flex DuoClean LED Headlight Replacement: passo 8, immagine 2 di 2

    • Turn the T10 Security Torx screwdriver counterclockwise to remove the 15mm screw.

    Modifica

  10. Shark Flex DuoClean LED Headlight Replacement: passo 9, immagine 1 di 2 Shark Flex DuoClean LED Headlight Replacement: passo 9, immagine 2 di 2

    • Use the metal spudger to pry off the clear, plastic cover on the LEDs.

    • Prying the cover off too aggressively may cause it to break.

    Modifica

  11. Shark Flex DuoClean LED Headlight Replacement: passo 10, immagine 1 di 1

    • Use wire cutters to detach the black cables from the LEDs on both sides.

    • Strip 1 cm off the ends of the wires, using a wire stripper.

    • Solder the exposed wires to the new LEDs.

    • Use the soldering guide in the Introduction.

    Modifica
Conclusione

To reassemble your device, follow these instructions in reverse order.

Autore

con 3 altri collaboratori

Samantha Mickelson

Membro da: 10/08/18

496 Reputazione

4 Guide realizzate

Distintivi: 9

+6 altri distintivi

Team

Cal Poly, Team S17-G5, White Fall 2018 Membro di Cal Poly, Team S17-G5, White Fall 2018

CPSU-WHITE-F18S17G5

4 Membri

14 Guide realizzate

0 Commenti

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 1

Ultimi 7 Giorni: 2

Ultimi 30 Giorni: 9

Tutti i Tempi: 1,362