Questa versione può contenere modifiche errate. Passa all'ultima istantanea verificata.
Cosa ti serve
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Orient the camera so the button panel and LCD are facing you.
-
Use a spudger or fingernail to open the battery compartment on the right side of the camera.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Push the blue trapdoor to the left to release the battery, and remove the battery.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a Phillips #00 screwdriver to remove the 4 mm screw inside the battery compartment.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the 4 mm Phillips #00 screw hiding in the external flash port.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the four 5 mm Phillips #00 screws from the lens assembly.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the metal lens mount by hand or with tweezers.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use tweezers to remove the inner metal ring.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a Phillips #00 screwdriver to remove the three 4 mm screws from the bottom of the case.
-
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use your hands to slowly pull the front casing away from the camera.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Gently flip the sensor cover back to expose the screw attaching the sensor cover to the ribbon cable.
-
Use a Phillips #00 screwdriver to remove the 3 mm screw from the sensor cover.
-
Use tweezers to remove the metal contact cover. Be sure to carefully remove the cover so the gold contacts remain in place.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the four 4 mm Phillips #00 screws holding the sensor mount in place.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the four 4 mm Phillips #00 screws securing the battery compartment to the mother board.
-
Remove the battery compartment.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a spudger to disconnect the ribbon cable connecting the image sensor to the motherboard.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Gently remove the sensor mount from the camera case.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a Phillips #00 screwdriver to remove the 3 mm screw located below the wifi antenna.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use tweezers to disconnect the wifi antenna from the motherboard.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a spudger to disconnect the LCD ribbon cable by prying it straight up from the motherboard.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a spudger to unlock the topmost ZIF connector by flipping open the black flap.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Insert the pointed end of a spudger into the hole in the middle of the ribbon cable.
-
Gently pull the spudger back to slide the ribbon cable out of its connector.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Disconnect the blue ribbon cable from the motherboard.
-
Insert the pointed end of a spudger into the hole in the top of the ribbon.
-
Gently pull the ribbon from the connector.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a Phillips #00 screwdriver to remove the two 5 mm screws holding the flash assembly to the camera case.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the flash assembly by gently pulling it away from the case.
-