Questa versione può contenere modifiche errate. Passa all'ultima istantanea verificata.
Cosa ti serve
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Flip the speaker upside down with the back panel of plugs pointed away from you.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the metal spudger to pry off the rubber bottom cover. It will be glued onto the bottom of the speaker.
-
Work the rubber cover off by slowly going all the way around with the metal spudger, applying as much force as needed.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Scrape most of the glue away to reveal the five flathead screws - four around the outside, and one in the middle.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the five 6 mm screws with a Phillips #2 screwdriver.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Lift off the metal plate. It will be surprisingly heavy and it is approximately 1cm thick.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Turn the speaker counter-clockwise 90 degrees.
-
Use a knife to cut along the left seam all the way down the length of the device.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
The casing should be easily removed by prying and lifting it off.
-
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Flip device 180 degrees so the light ring/button panel is on top with the 'Elite' facing you.
-
Remove one 6 mm screw with a Phillips #2 screwdriver.
-
Spin the device so the opposite side is facing you.
-
Remove the two 6 mm screws with a Phillips #2 screwdriver.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Carefully remove the top panel, light ring, button panel, and the corresponding board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Peel off all rubber strips along sides, middle front and middle back of the device.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the eight 6 mm screws using the Phillips #2 screwdriver.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Pry apart the two sides carefully. The halves will not be able to separate completely because of wires and the motherboard.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Slide the motherboard out using your hands.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Slide out ribbon-like wire at the bottom of the speaker using your hands.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove two of the wire connectors with your hands or with tweezers.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the two wire connectors using tweezers or your fingers. Be careful not to damage the plastic.
-
Remove the 3 pieces of hot glue using tweezers. Don't worry about ripping the foam covering the cords.
-
Remove the ribbon wire by pulling on it with tweezers.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Peel away the off white glue and disconnect the wires from the motherboard.
-
Remove the motherboard from the device.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the eight 6 mm screws with a Phillips #2 screwdriver.
-
Lift the subwoofers out and remove them from the device.
-
Annulla: non ho completato questa guida.
Un'altra persona ha completato questa guida.