Questa versione può contenere modifiche errate. Passa all'ultima istantanea verificata.
Cosa ti serve
-
-
Rimuovi le dieci viti seguenti, che fissano il case inferiore al MacBook Pro Unibody da 13":
-
Sette viti con testa a croce da 3 mm.
-
Tre viti con testa a croce da 13,5 mm.
-
-
-
Solleva leggermente il case inferiore e spingilo verso la parte posteriore del computer per liberare le linguette di montaggio.
-
-
-
Mediante l'estremità piatta di uno spudger, sollevare il connettore del cavo della batteria dal connettore femmina sulla scheda logica staccandolo da questa.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the flat end of a spudger to pry the subwoofer/right speaker cable connector up off its socket on the logic board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Disconnect the camera cable by sliding it horizontally out of its socket.
-
If you see a small plastic retainer stuck to the logic board that prevents the camera cable from sliding out, peel it up carefully from the logic board. Apply a little heat from a hair dryer or heat gun if necessary to help soften the adhesive holding it in place. Do not attempt to forcibly disconnect the cable with the retainer in place.
-
If you still have trouble, use the point of a spudger to push at each side of the connector and "walk" it slowly from its socket.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
De-route the camera data cable from the channel in the optical drive.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the following screws securing the camera data cable and right speaker to the upper case:
-
Two 8 mm Phillips screws.
-
One 4mm Phillips screw.
-
Slide the camera cable bracket out from under the subwoofer and remove it from the computer.
-
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Grab the plastic pull tab secured to the display data cable lock and rotate it toward the DC-in side of the computer.
-
Pull the display data cable connector straight away from its socket.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the following two screws securing the display data cable bracket to the upper case:
-
One 7 mm Phillips screw.
-
One 5 mm Phillips screw.
-
Lift the display data cable bracket out of the upper case.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use your Torx driver to remove the two outer 6.5 mm screws securing each of the two display brackets to the upper case (4 screws total).
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Open your MacBook so the display is perpendicular to the upper case.
-
Place your opened MacBook on a table as pictured.
-
While holding the display and upper case together with your left hand, use your Torx driver to remove the remaining 6.5 mm screw from the lower display bracket.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the last remaining 6 mm Torx screw securing the display to the upper case.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Grab the upper case with your right hand and rotate it slightly toward the top of the display so the upper display bracket clears the edge of the upper case.
-
Rotate the display slightly away from the upper case.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Lift the display up and away from the upper case, minding any brackets or cables that may get caught.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Grab the clutch cover as shown and slide it toward the right side of the display.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Gently rock the clutch cover back and forth on its long axis while pulling it away from the display.
-
Do this action along the length of the clutch cover until you can lift it off the framework attaching it to the display.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the single 5.2 mm T6 Torx screw securing the left clutch hinge nearest the display glass.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the remaining two 5.2 mm T6 Torx screws securing the left clutch hinge to the display.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the left clutch hinge from the display.
-
Annulla: non ho completato questa guida.
Altre 11 persone hanno completato questa guida.