Questa versione può contenere modifiche errate. Passa all'ultima istantanea verificata.
Cosa ti serve
-
-
Usa una moneta o uno spudger per ruotare la vite di bloccaggio della batteria di 90 gradi in senso orario.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the three evenly-spaced Phillips screws from along the rear wall of the battery compartment.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Lift up on L-shaped memory cover, slide it to the right, and lift it out of the computer.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the following 3 screws:
-
One 11 mm Phillips #00 in the middle of the case.
-
Two 14.5 mm Phillips #00.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the following 3 screws from the rear wall of the battery compartment:
-
Two 3 mm Phillips #00. (A1181 has three 3 mm screws and one 4 mm.)
-
One 4 mm Phillips #00 on the right side.
-
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the two 6 mm Phillips #00 screws from either side of the right wall of the battery compartment (not the ones closest to the battery connector).
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the four 3 mm indicated Phillips #00 screws from the front wall of the battery compartment. When working from the left, remove the 2nd, 4th, 7th and 9th screw.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the following 4 screws from the back of the computer:
-
Two 7 mm shouldered Phillips on the far sides.
-
Two 10.5 mm Phillips toward the center.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the two 5.2 mm shouldered Phillips #00 screws from the optical side of the computer.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Starting near the display and working around to the front of the computer, pry up on the upper case. It is held with clips on the right above the optical drive. These will release with some firm lifting pressure.
-
Be careful when prying up the upper case. It's very easy to slice open a fingertip and thus provide the blood sacrifice the Mac gods sometimes require of those who insist on doing their own repairs.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
While holding up the upper case (from the bottom or the top), use a spudger to pry up the orange trackpad and keyboard cable from its connector.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the single Phillips screw near the battery connector.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the small black plastic spacer from the computer.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the two Phillips screws attaching the battery connector to the lower case.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a spudger to carefully pry the battery connector up and disconnect it from the logic board.
-
Annulla: non ho completato questa guida.
Altre 25 persone hanno completato questa guida.
2 Commenti
My rev 1,1 white Macbook was missing the spacer.
So was mine. Also make note for comparison, the Apple Service Source manual states that the I/O Panel needs to be removed prior to removing the connector - happily, according to iRobot, you don’t have to.