Questa versione può contenere modifiche errate. Passa all'ultima istantanea verificata.
Cosa ti serve
-
-
Usa una moneta o uno spudger per ruotare la vite di bloccaggio della batteria di 90 gradi in senso orario.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the three evenly-spaced Phillips screws from along the rear wall of the battery compartment.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Lift up on L-shaped memory cover, slide it to the right, and lift it out of the computer.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the following 3 screws:
-
One 11 mm Phillips #00 in the middle of the case.
-
Two 14.5 mm Phillips #00.
-
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the following 3 screws from the rear wall of the battery compartment:
-
Two 3 mm Phillips #00. (A1181 has three 3 mm screws and one 4 mm.)
-
One 4 mm Phillips #00 on the right side.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the two 6 mm Phillips #00 screws from either side of the right wall of the battery compartment (not the ones closest to the battery connector).
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the four 3 mm indicated Phillips #00 screws from the front wall of the battery compartment. When working from the left, remove the 2nd, 4th, 7th and 9th screw.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the following 4 screws from the back of the computer:
-
Two 7 mm shouldered Phillips on the far sides.
-
Two 10.5 mm Phillips toward the center.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the two 5.2 mm shouldered Phillips #00 screws from the optical side of the computer.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Starting near the display and working around to the front of the computer, pry up on the upper case. It is held with clips on the right above the optical drive. These will release with some firm lifting pressure.
-
Be careful when prying up the upper case. It's very easy to slice open a fingertip and thus provide the blood sacrifice the Mac gods sometimes require of those who insist on doing their own repairs.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
While holding up the upper case (from the bottom or the top), use a spudger to pry up the orange trackpad and keyboard cable from its connector.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Disconnect the two antenna cables from the Airport card on the left side of the computer.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the following 2 screws from the Airport card:
-
One 3 mm Phillips from the left side.
-
One 8 mm Phillips from the right side.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Grasp the Airport card at its top and slide it toward the screen and out of the computer.
-
Annulla: non ho completato questa guida.
Altre 111 persone hanno completato questa guida.
5 Commenti
You'll have to remove a lot of different sized screws. Be careful to take care of properly placing them while doing the steps - you'll have to put them back the way you took them out. I personally placed them the way the pictures show them.
Thank you thank you thank you. A lifelong PC user, with their wife's MacBook ( so lots of pressure not to break it) was able to follow this walk through and make their wife so happy with the improved performance. Thanks for giving me the confidence to tackle other upgrades that can be done on this MacBook!
-Geoff K
These instructions were really fantastic. SO easy to follow, and I'm especially glad that there was a video which reinforced the written instructions. Thank you!
do you have any idea for the laptop vostro 1000 how?