Questa versione può contenere modifiche errate. Passa all'ultima istantanea verificata.
Cosa ti serve
-
Attrezzo utilizzato in questo passaggio:P5 Pentalobe Screwdriver Retina MacBook Pro and Air$5.99
-
Rimuovi le seguenti dieci viti:
-
Due viti a cinque punte Pentalobe da 9 mm
-
Otto viti a cinque punte Pentalobe da 2,6 mm
-
-
-
Afferra la linguetta di plastica trasparente collegata al connettore della batteria e tirala verso il bordo anteriore dell'Air per scollegare la batteria dalla scheda logica.
-
-
-
-
Solleva la batteria dal bordo più vicino alla scheda logica e rimuovila dal case superiore.
-
Caricala al 100% e lasciala caricare per almeno altre due ore. Poi, scollegalo e usalo normalmente per scaricare la batteria. Quando vedi l'avviso di batteria scarica, salva il tuo lavoro e tieni acceso il computer finché non si sospende a causa della batteria scarica. Aspetta almeno 5 ore, poi carica il tuo laptop ininterrottamente fino al 100%.
-
Se noti comportamenti o problemi strani dopo aver installato la nuova batteria, potresti dover reimpostare l'SMC del tuo MacBook.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the tip of a spudger or your fingernail to flip up the retaining flap on the trackpad ribbon cable ZIF socket.
-
Pull the trackpad ribbon cable straight out of its socket toward the rear edge of the Air.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
While carefully lifting the keyboard ribbon cable with one hand, use the tip of a spudger or your fingernail to flip up the retaining flap on the keyboard ribbon cable ZIF socket.
-
Pull the keyboard ribbon cable straight out of its socket toward the front edge of the Air.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the following twelve screws:
-
Six 1.6 mm Phillips screws securing the trackpad to the upper case.
-
Six 1.6 mm Phillips screws securing the trackpad brackets to the trackpad.
-
A Phillips #000 should be sufficient, but a JIS #000 may also work as well.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the right and left trackpad brackets from the upper case.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the 1.4 mm T5 Torx set screw from its tapped hole near the front edge of the upper case.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the flat edge of a spudger to carefully lift the edge of the trackpad closest to the keyboard from its recess in the upper case by lifting it away from the brackets attached to the upper case.
-
Remove the trackpad from the upper case.
-
Annulla: non ho completato questa guida.
Altre 19 persone hanno completato questa guida.
3 Commenti
The screws are not Philips 00. They are smaller than Philips 000. I am looking for a screwdriver in that size.
I have the iFixit toolkit, and the PH000 tip simply did not fit into the head. The J000 tip could remove a couple screws, but started to strip the head of two others before I stopped. The tip almost stripped the two I removed on reinsertion.
The replacement trackpad comes with a set of these screws.
No pictures : impossible to use
Hey Pierre! There was an Amazon service outage that affected the images on this page. Take another look, you should be able to follow this guide now! =)