Questa versione può contenere modifiche errate. Passa all'ultima istantanea verificata.
Cosa ti serve
-
Attrezzo utilizzato in questo passaggio:P5 Pentalobe Screwdriver Retina MacBook Pro and Air$5.99
-
Svita le seguenti dieci viti:
-
Due viti Pentalobe 5-Point da 8 mm
-
Otto viti Pentalobe 5-Point da 2,5 mm
-
-
-
Usa la parte piatta di uno spudger per fare leva su entrambi i lati del connettore della batteria per scollegarlo dalla sua presa sulla scheda madre.
-
Piega leggermente il cavo della batteria lontano dalla scheda madre in modo che non torni a far contatto con la sua presa.
-
-
-
-
Rimuovi le seguenti cinque viti che fissano la batteria alla parte superiore:
-
Due viti T5 Torx da 5,2 mm
-
Una vite T5 Torx da 6 mm
-
Due viti T5 Torx da 2,6 mm
-
-
-
Solleva la batteria dal bordo più vicino alla scheda logica e rimuovila dalla parte superiore.
-
Caricala al 100% e continua a caricarlo per almeno altre 2 ore. Poi, scollegala e utilizza il dispositivo finché scarico. Quando vedi l'avviso di batteria scarica, salva il lavoro e lascia acceso il computer fin quando si spegne a causa della batteria scarica. Attendi 5 ore, poi carica il computer portatile ininterrottamente al 100%.
-
Se noti qualche comportamento insolito o problemi dopo l'installazione della nuova batteria, potrebbe essere necessario ripristinare l'SMC del MacBook.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the point of a spudger to lift the ZIF connector retaining flap on the trackpad data cable.
-
Gently slide the ribbon cable out of the ZIF connector.
-
Adjust, but do not remove the T5 Trackpad Sensitivity Screw to change the trackpad's depth sensitivity.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
With one hand, push the keyboard ribbon cable in slightly to access the ZIF connector beneath it.
-
Use a spudger to flip up the retaining flap.
-
Gently slide the cable out of the connector.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the six 1.5 mm Phillips #00 screws holding the trackpad in place.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Open the device about 10 degrees.
-
While holding the bottom of the trackpad, press up on the side of the trackpad closest to the logic board to free it from the upper case.
-
Remove the trackpad from the device.
-
Annulla: non ho completato questa guida.
Altre 8 persone hanno completato questa guida.
3 Commenti
help me pleaseeeeee
Thanks Sam. I had to make one adjustment in order to get the keyboard ribbon cable back in. Using a Magnifier with a light (thanks Pablo), I held the MBA in a 90 degree position under the Magnifier with a light and I was able to clearly see so that I could slide the ribbon back in to the connector.
ALERT TO ALL OWNERS OF THE MacBook Air 11" Early 2014: if you need to replace your trackpad, make sure you determine in advance whether the data cable that connects your logic board to the trackpad’s ZIF connector has 20 pins or 14 pins. Mine has 20 pins and DOES NOT match the one pictured in the iFixit tutorial. It is my understanding that both of those two different trackpads have the same part number: 923-0429, but they are not interchangeable.