Aggiusta la tua roba Comunità Store

Logitech Harmony Smart Control Hub Light Bulb Replacement

Introduzione

Learn how to disassemble the Logitech Harmony Smart Control hub, remove a burned out or defective light bulb or bulb(s), and replace it with new one(s).

This repair requires soldering. View the soldering guide at:

Soldering Guide

Cosa ti serve

  1. Logitech Harmony Smart Control Hub Light Bulb Replacement, Light Bulb: passo 1, immagine 1 di 2 Logitech Harmony Smart Control Hub Light Bulb Replacement, Light Bulb: passo 1, immagine 2 di 2

    • Use a spudger to lift up one of the rubber pads on the bottom of the hub.

    • Pull back the rubber pad and remove it. This will expose the screws on the bottom of the device.

    • Repeat for the second rubber pad.

    Modifica

  2. Logitech Harmony Smart Control Hub Light Bulb Replacement: passo 2, immagine 1 di 2 Logitech Harmony Smart Control Hub Light Bulb Replacement: passo 2, immagine 2 di 2

    • Use a PH00 screwdriver bit to remove the four 6mm Phillips screws on the bottom of the device.

    Modifica

  4. Logitech Harmony Smart Control Hub Light Bulb Replacement: passo 3, immagine 1 di 2 Logitech Harmony Smart Control Hub Light Bulb Replacement: passo 3, immagine 2 di 2

    • Use a spudger to separate the top and bottom pieces of the device.

    Modifica

  5. Logitech Harmony Smart Control Hub Light Bulb Replacement: passo 4, immagine 1 di 2 Logitech Harmony Smart Control Hub Light Bulb Replacement: passo 4, immagine 2 di 2

    • Use the PH00 screwdriver bit to unscrew the three 4mm Phillips screws on the control board.

    Modifica

  6. Logitech Harmony Smart Control Hub Light Bulb Replacement: passo 5, immagine 1 di 2 Logitech Harmony Smart Control Hub Light Bulb Replacement: passo 5, immagine 2 di 2

    • Place the end of the opening tool under the yellow corner of the circuit board as shown.

    • Gently push upward to pry the board from its housing.

    Modifica

  7. Logitech Harmony Smart Control Hub Light Bulb Replacement: passo 6, immagine 1 di 3 Logitech Harmony Smart Control Hub Light Bulb Replacement: passo 6, immagine 2 di 3 Logitech Harmony Smart Control Hub Light Bulb Replacement: passo 6, immagine 3 di 3

    • Determine which of the five bulbs are defective.

    • Turn the board over to expose the bulb solder.

    • Using a soldering iron, remove the solder and bulb. Replace with a new bulb and re-solder.

    Modifica
Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 2 persone hanno completato questa guida.

Autore

con 7 altri collaboratori

Josh Hendricks

Membro da: 09/17/15

464 Reputazione

4 Guide realizzate

Distintivi: 7

+4 altri distintivi

Team

IUPUI, Team 3-2, Harley Fall 2015 Membro di IUPUI, Team 3-2, Harley Fall 2015

IUPUI-HARLEY-F15S3G2

4 Membri

5 Guide realizzate

0 Commenti

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 1

Ultimi 30 Giorni: 1

Tutti i Tempi: 532