Salta al contenuto principale

Logic Board Disconnection

Solo Prerequisita
Questa guida è destinata a essere usata solo come prerequisito per altre guide. Da sola è incompleta.

Cosa ti serve

  1. Logic Board Disconnection, Disconnect the logic board: passo 1, immagine 1 di 2 Logic Board Disconnection, Disconnect the logic board: passo 1, immagine 2 di 2
    • Use a T3 Torx driver to remove the two 1.4 mm screws securing the trackpad connector bracket.

    • Remove the trackpad connector bracket.

  2. Logic Board Disconnection: passo 2, immagine 1 di 2 Logic Board Disconnection: passo 2, immagine 2 di 2
    • Use the flat end of a spudger to pry the trackpad cable connector up and out of its socket.

  3. Logic Board Disconnection: passo 3, immagine 1 di 3 Logic Board Disconnection: passo 3, immagine 2 di 3 Logic Board Disconnection: passo 3, immagine 3 di 3
    • If the left speaker is already disconnected, skip this step.

    • Slide the tip of a spudger underneath the left speaker cable and pry straight up to disconnect the speaker.

    • With the connector disconnected, slide the flat end of a spudger under the cable to separate the adhesive securing the cable to the logic board.

  4. Logic Board Disconnection: passo 4, immagine 1 di 2 Logic Board Disconnection: passo 4, immagine 2 di 2
    • Use a T3 Torx driver to remove the two 1.3 mm screws securing the USB-C port connector bracket.

    • Remove the USB-C connector bracket.

  5. Logic Board Disconnection: passo 5, immagine 1 di 2 Logic Board Disconnection: passo 5, immagine 2 di 2
    • Use the flat end of a spudger to pry the USB-C cable connector up and out of its socket on the logic board.

  6. Logic Board Disconnection: passo 6, immagine 1 di 3 Logic Board Disconnection: passo 6, immagine 2 di 3 Logic Board Disconnection: passo 6, immagine 3 di 3
    • Use a spudger to lift up the small locking flap on the sound board cable's ZIF connector.

    • Slide the sound board cable out of the ZIF connector.

  7. Logic Board Disconnection: passo 7, immagine 1 di 1
    • Peel back the black tape covering the fan cable connector.

  8. Logic Board Disconnection: passo 8, immagine 1 di 3 Logic Board Disconnection: passo 8, immagine 2 di 3 Logic Board Disconnection: passo 8, immagine 3 di 3
    • Use the tip of a spudger to lift up the locking flap on the fan cable's ZIF connector.

    • Slide the fan cable out of the ZIF connector.

  9. Logic Board Disconnection: passo 9, immagine 1 di 2 Logic Board Disconnection: passo 9, immagine 2 di 2
    • Use a T3 Torx driver to remove the two 1.4 mm screws securing the antenna cable bracket.

    • Remove the antenna cable bracket.

  10. Logic Board Disconnection: passo 10, immagine 1 di 3 Logic Board Disconnection: passo 10, immagine 2 di 3 Logic Board Disconnection: passo 10, immagine 3 di 3
    • Insert the point of a spudger under one of the antenna cables close to the connector. Pry straight up to disconnect the cable.

    • Repeat for the other antenna cable.

  11. Logic Board Disconnection: passo 11, immagine 1 di 2 Logic Board Disconnection: passo 11, immagine 2 di 2
    • Use a T3 Torx driver to remove the two 1.5 mm screws securing the display cable connector bracket.

    • Remove the display cable connector bracket.

  12. Logic Board Disconnection: passo 12, immagine 1 di 2 Logic Board Disconnection: passo 12, immagine 2 di 2
    • Use the flat end of a spudger to pry up the display cable connector.

Conclusione

To reassemble your device, follow these instructions in reverse order.

Adam O'Camb

Membro da: 04/11/15

196.626 Reputazione

416 Guide realizzate

0 Commenti

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 6

Ultimi 30 Giorni: 7

Tutti i Tempi: 122