Jawbone Big Jambox Button Circuit Board Replacement

Ultimo aggiornamento il June 23, 2015

20 - 30 minuti

Moderato

Introduzione

If resetting your Big Jambox does not work, these are the instructions on how to replace the button circuit board. This is a longer process because you will need to also remove the speakers.

Cosa ti serve

Strumenti

Mostra di più…

Passo 1 Outer Case

Jawbone Big Jambox Button Circuit Board Replacement, Outer Case: passo 1, immagine 1 di 1

Remove both end caps by putting a plastic opening tool in the center of the seam. Work around the edges to pry the end caps off completely.
Due to interior clips holding the end caps in place, use caution when applying force.

Modifica

Passo 2

Jawbone Big Jambox Button Circuit Board Replacement: passo 2, immagine 3 di 3

Turn the Jambox upside down. Peel the indicated rubber tabs off, using a plastic opening tool if necessary.
You may want to only take the tabs half way off to avoid re-gluing when reassembling.
Remove the three T6, 7.0 mm screws under each rubber tab.
Because the screws are a different length, set the screws aside.

Modifica

Passo 3

Jawbone Big Jambox Button Circuit Board Replacement: passo 3, immagine 3 di 3

With the Jawbone logo facing towards you and with correct orientation, place the Jambox with the left end cap facing upward.
Unscrew indicated T6 9.7 mm screws.
Gently loosen the tabs from their anchor points so the bottom may be removed.
Flip the Jambox so the other end cap is facing up. The USB cable is on this side (metal grounding clip, indicated in orange). Repeat the above two steps.

Modifica

Passo 4

Pry up the bottom panel by lifting from the device.
Pull the bottom up. This may take a bit of force as the bottom is glued to device.
Once removed, the battery will now be visible.

Modifica

Passo 5

Before unscrewing, take a picture of the top view. That way, when you're reassembling the device, you'll know the orientation of the metal grounding plates.
Unscrew the eight indicated T6 9.8 mm screws. Remove metal grounding plates.

Modifica

Passo 6

Once all eight screws are removed, pry the sides of the Jambox to lift the body from it's shell.

Modifica

Passo 7

With the battery facing forward, remove the three indicated T6 9.5 mm screws.
Once the screws are removed, lift up the small plastic plate, revealing the auxiliary board underneath.

Modifica

Passo 8 Button Panel

Jawbone Big Jambox Button Circuit Board Replacement, Button Panel: passo 8, immagine 1 di 2

Jawbone Big Jambox Button Circuit Board Replacement, Button Panel: passo 8, immagine 2 di 2

Turn the Jambox so that the button panel is visible.
Remove the indicated screws, T6 9.6 mm.
There is a small plastic flap obscuring the view of one of the screws, indicated in orange. In order to unscrew it, simply lift the flap out of the way.

Modifica

Passo 9

Pop off the button panel.

Modifica

Passo 10

Remove the colored ribbon that connects the green button circuit board to the blue auxiliary board by using your finger to lift the small black tabs that clamp down the ribbon.

Modifica

Passo 11 Speaker

Jawbone Big Jambox Button Circuit Board Replacement, Speaker: passo 11, immagine 1 di 3

Jawbone Big Jambox Button Circuit Board Replacement, Speaker: passo 11, immagine 2 di 3

Jawbone Big Jambox Button Circuit Board Replacement, Speaker: passo 11, immagine 3 di 3

Place the disassembled Jambox with the speakers facing up.
Locate the screws around the broken speaker.
Use a T15 screwdriver to remove the four 12.1 mm screws around the broken speaker.

Modifica

Passo 12

Using a plastic opening tool, pry the speaker out of the Jambox.

Modifica

Passo 13

Desolder the wires from the speaker terminal in the Jambox.
Detach the round speaker from its square frame, and save the square frame for the replacement speaker.
Use caution when operating a soldering iron due to extreme heat.
For instructions on how to solder and desolder, take a look at the soldering guide.