Salta al contenuto principale

Aggiusta la tua roba

Diritto alla Riparazione

Componenti & Strumenti

Introduzione

The charging port bay contains the USB-C port required to charge your JBL Charge 4. It also includes an AUX port to play music and a USB out port to charge your device. If one or more of these ports is not working this guide will show you how to replace them. This guide requires knowledge of desoldering. Find a guide on soldering and desoldering here.

  1. Flip your speaker over and insert the plastic opening tool into the slit on the grille.
    • Flip your speaker over and insert the plastic opening tool into the slit on the grille.

    • Pry away from yourself towards the back of the speaker to release the clip.

    • Repeat this process for the clip on the other side.

  2. Remove the two 8mm Phillips #0 screws from the other edge of the grille. Remove the two 8mm Phillips #0 screws from the other edge of the grille.
    • Remove the two 8mm Phillips #0 screws from the other edge of the grille.

  3. Pull apart both sides of the grille.
    • Pull apart both sides of the grille.

    • Lift the cover off of the speaker.

  4. Using the plastic opening tool,  lift the tab on top of the speaker to release the radiator from the clips. Repeat this process on the other clips around the radiator to release it from the frame.
    • Using the plastic opening tool, lift the tab on top of the speaker to release the radiator from the clips.

    • Repeat this process on the other clips around the radiator to release it from the frame.

  5. Push the radiator off of the frame of the device. Repeat on the other side.
    • Push the radiator off of the frame of the device.

    • Repeat on the other side.

    • The passive bass radiators seal out water from inside the device. Removing them multiple times may compromise the waterproof nature of the speaker.

  6. LCD iPhone Screen Fix Kits

    The budget option, covered by our Lifetime Warranty.

    Shop Kits

    LCD iPhone Screen Fix Kits

    Cut repair costs, not quality.

    Shop Kits
  7. Remove the two 6mm Phillips #0 screws from either side to remove the port bay cover. Remove the two 6mm Phillips #0 screws from either side to remove the port bay cover.
    • Remove the two 6mm Phillips #0 screws from either side to remove the port bay cover.

  8. There are two hooks that attach the opposite side of the port bay cover to the device. Slide the cover back and off the hooks.
    • There are two hooks that attach the opposite side of the port bay cover to the device. Slide the cover back and off the hooks.

    • Remove the port bay cover.

  9. Remove the four 6mm Phillips #0 screws. Remove the four 6mm Phillips #0 screws.
    • Remove the four 6mm Phillips #0 screws.

  10. Before removing  port bay you must detach the connecting tabs on either side of the device. Press on the tab and gently pull out the wire connector.
    • Before removing port bay you must detach the connecting tabs on either side of the device.

    • Press on the tab and gently pull out the wire connector.

  11. Remove the second connector on the opposite side by gently pulling it out. Remove the second connector on the opposite side by gently pulling it out.
    • Remove the second connector on the opposite side by gently pulling it out.

  12. Remove the port bay from the device and place the device to the side.
    • Remove the port bay from the device and place the device to the side.

  13. Remove the three 9mm Phillips #0 screws from the board. Remove the three 9mm Phillips #0 screws from the board.
    • Remove the three 9mm Phillips #0 screws from the board.

  14. Using the plastic opening tool, lift the board from the port bay holder. Using the plastic opening tool, lift the board from the port bay holder.
    • Using the plastic opening tool, lift the board from the port bay holder.

  15. Choose which port you want to replace. Turn the board around and desolder the connection to remove the chosen port.
    • Choose which port you want to replace.

    • Turn the board around and desolder the connection to remove the chosen port.

    • A guide for soldering and desoldering can be found here.

Conclusione

To reassemble your device, follow these instructions in reverse order.

Un'altra persona ha completato questa guida.

Team

Cal Poly, Team S1-G1, White Winter 2019 Membro di Cal Poly, Team S1-G1, White Winter 2019

CPSU-WHITE-W19S1G1

4 Membri

14 Guide realizzate

Does anybody know which exact ports I have to get? There are a ton of different models out there.

Ulpi - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 7

Ultimi 7 Giorni: 69

Ultimi 30 Giorni: 259

Tutti i Tempi: 2,005