Questa versione può contenere modifiche errate. Passa all'ultima istantanea verificata.
Cosa ti serve
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
The microSD card tray is located on the upper right hand side of the phone, above the volume buttons. To open the tray, insert a microSD card eject tool, or a paperclip, into the small hole in the microSD card tray.
-
Then press the tool or paperclip to eject the microSD card tray.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Insert a SIM card eject tool or a paperclip into the small hole besides the SIM card tray, located on the upper section of the left edge of the phone.
-
Press to eject the tray.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Using a plastic opening pick or a spudger, gently pry and remove the cover on top of the case.
-
Remove the two 4 mm T5 Torx screws on the top of the case.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Work a plastic opening pick around the perimeter of the device to separate the rear case from the display assembly.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a pair of tweezers to get underneath the white and blue cable connectors and gently push them upwards to disconnect them.
-
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the two 1.5 mm screws that secure the battery connector to the motherboard, using a Phillips #00 screwdriver.
-
Use a spudger to gently pry up the battery connector from its socket.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Peel back the Kapton tape from the ZIF connectors.
-
Use a spudger or your fingernail to lift the hinged retainer clips on the ZIF connectors, and gently slide the cables out.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Using the tweezers, carefully lift the tape covering the electrical strip, as shown in the picture.
-
Use a spudger or your fingernail to lift the hinged retainer clip on the ZIF connector, and slide the cable out.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Peel back the Kapton tape from the remaining three ZIF connectors, then use a spudger or your fingernail to lift the hinged retainer clips on the ZIF connectors, and slide the cables out from each.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the dual LED flash cover with a pair of tweezers. The cover is held on with a small amount of adhesive.
-
Use a pair of tweezers to disconnect the two antenna cables near the camera.
-
Disconnect the antenna cable near the bottom right of the phone.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the three 4 mm T5 Torx screws that secure the motherboard.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a pair of tweezers to lift the vibrator out of its slot.
-
Use an iOpener or heat gun to loosen the adhesive at the bottom of the motherboard.
-
Use a plastic opening tool, or a spudger, along the edges of the case to gently pry the motherboard out of the case.
-
Gently lift the motherboard out of the case, beginning from the top corner (near the camera).
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Using tweezers, remove the tape from the bottom of the battery.
-
Use a spudger to carefully pry the battery up from the display assembly.
-
Annulla: non ho completato questa guida.
Altre 42 persone hanno completato questa guida.
19 Commenti
I replaced the battery now but encountered a problem, as my phone wasn't working properly afterwards. When I switched on, it kind of reset to default and the play store app kept crashing, so I had to do a factory reset
Done all of this by the book but phone won't turn on charge screen lights up and charges but still won't turn on please help
You tore the power and volume button cable. It's a $10 replacement, no big deal. I did the same thing even after having repaired phones for years now.
Jonah -