Aggiusta la tua roba Comunità Store

HP Windows Mixed Reality Controllers TPC-Q044 Joystick Switch Replacement

Introduzione

This guide goes over how to replace the controller's joystick on the circuit board.

If you are experiencing problems with the joystick, you will want to open up the device to fix the problem. A common solution associated with this problem is to take a small dry tissue or towel and clean the parts of the controller to ensure there is no debris limiting the joystick’s range of motion. If that doesn’t work, move the shaft underneath the joystick around to see how fluid it is. If the shaft is the problem, the joystick component will have to be replaced.

To complete this task you will need the indicated screwdriver and spudger. Note that you will need to solder to replace the joystick component which can be a potential danger.

Cosa ti serve

  1. HP Windows Mixed Reality Controllers TPC-Q044 Joystick Switch Replacement, Batteries: passo 1, immagine 1 di 3 HP Windows Mixed Reality Controllers TPC-Q044 Joystick Switch Replacement, Batteries: passo 1, immagine 2 di 3 HP Windows Mixed Reality Controllers TPC-Q044 Joystick Switch Replacement, Batteries: passo 1, immagine 3 di 3

    • Slide the rear compartment cover in the direction of the arrow.

    • If replacing batteries, ensure the (+) and (-) on the battery match the (+) and (-) labeled in the battery compartment.

    Modifica

  2. HP Windows Mixed Reality Controllers TPC-Q044 Joystick Switch Replacement, Shell: passo 2, immagine 1 di 2 HP Windows Mixed Reality Controllers TPC-Q044 Joystick Switch Replacement, Shell: passo 2, immagine 2 di 2

    • Remove the four 4mm screws using a Phillips #00 screwdriver.

    Modifica

  3. HP Windows Mixed Reality Controllers TPC-Q044 Joystick Switch Replacement: passo 3, immagine 1 di 3 HP Windows Mixed Reality Controllers TPC-Q044 Joystick Switch Replacement: passo 3, immagine 2 di 3 HP Windows Mixed Reality Controllers TPC-Q044 Joystick Switch Replacement: passo 3, immagine 3 di 3

    • Grip the main body and pull the joystick outwards until the entire front panel pops off.

    • Remove the 6mm screw in the corner of the joystick well using a Phillips #00 screwdriver.

    Modifica

  5. HP Windows Mixed Reality Controllers TPC-Q044 Joystick Switch Replacement: passo 4, immagine 1 di 2 HP Windows Mixed Reality Controllers TPC-Q044 Joystick Switch Replacement: passo 4, immagine 2 di 2

    • Use a spudger to pry apart the two halves of the assembly.

    • Work slowly, prying a small section at a time until the halves are completely separated.

    Modifica

  6. HP Windows Mixed Reality Controllers TPC-Q044 Joystick Switch Replacement, Small Circuit Board: passo 5, immagine 1 di 2 HP Windows Mixed Reality Controllers TPC-Q044 Joystick Switch Replacement, Small Circuit Board: passo 5, immagine 2 di 2

    • Using a Phillips #00 screwdriver, remove the four 4mm screws located on the joystick circuit board underneath the top half of the controller.

    Modifica

  7. HP Windows Mixed Reality Controllers TPC-Q044 Joystick Switch Replacement: passo 6, immagine 1 di 3 HP Windows Mixed Reality Controllers TPC-Q044 Joystick Switch Replacement: passo 6, immagine 2 di 3 HP Windows Mixed Reality Controllers TPC-Q044 Joystick Switch Replacement: passo 6, immagine 3 di 3

    • Remove the orange flat cable by pulling the orange tab parallel to the circuit board.

    • Release the blue flat cable by lifting up the white latch with a spudger.

    Modifica

  8. HP Windows Mixed Reality Controllers TPC-Q044 Joystick Switch Replacement, Joystick Switch: passo 7, immagine 1 di 2 HP Windows Mixed Reality Controllers TPC-Q044 Joystick Switch Replacement, Joystick Switch: passo 7, immagine 2 di 2

    • The joystick controller is soldered directly to the circuit board. You can find instructions for removing soldered components here.

    • The joystick controller is secured by 12 solder connections. Once these have been desoldered, the controller can be removed.

    Modifica
Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 3 persone hanno completato questa guida.

Autore

con 3 altri collaboratori

Clement Cheung

Membro da: 01/24/19

643 Reputazione

5 Guide realizzate

Distintivi: 13

+10 altri distintivi

Team

Cal Poly, Team S18-G5, White Winter 2019 Membro di Cal Poly, Team S18-G5, White Winter 2019

CPSU-WHITE-W19S18G5

2 Membri

14 Guide realizzate

2 Commenti

You can solder replacement Xbox One analog sticks right? I have some stick drift and can’t test this until my university reopens, but when it does I want to try fixing it.

Edit: I have the Dell controllers but they seem identical to the HP ones in this guide.

Vincent - Replica

I think this might be the stick: https://www.mouser.com/ProductDetail/Alp...

Alps RKJXV 23 degree 10K ohm multi-directional switches

I haven’t soldered it yet so do not take my word as fact, it just looks right.

Vincent - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 4

Ultimi 7 Giorni: 8

Ultimi 30 Giorni: 15

Tutti i Tempi: 1,210