Questa versione può contenere modifiche errate. Passa all'ultima istantanea verificata.
Cosa ti serve
-
-
Con il case chiuso, posiziona il lato superiore del Mini 1000 verso il basso su una superficie piana.
-
Spingi entrambi i ganci di rilascio della batteria l'uno verso l'altro.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the following two screws:
-
One 6 mm Phillips screw
-
One 4 mm Phillips screw
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
While pushing through the opening with one hand, grasp the left upper edge with the other hand and slightly pull the keyboard towards you.
-
Once an opening has been established, grasp the keyboard and slowly lift it upwards along the upper perimeter of the top edge.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Lift the keyboard out of the upper case, minding the cable that is still connecting it to the motherboard.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use your fingernail or the flat end of a spudger to flip up the retaining flap on the keyboard cable ZIF socket.
-
Pull the cable out of its socket and remove the keyboard.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use your fingernail or the flat end of a spudger to flip up the retaining flap on the SIM card ribbon cable ZIF socket.
-
Pull the SIM card ribbon cable out of its socket and peel it off the top of the hard drive enclosure.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use your fingernail or the flat end of a spudger to flip up the retaining flap on the hard drive cable ZIF socket.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the two 4.5 mm Phillips screws securing the hard drive to the lower case.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Lift the hard drive up and out of the lower case, being careful not to damage its cable in the process.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Using the sharp tip of a spudger, pry and remove the four plastic screw covers from the underside of the HP Mini 1000.
-
The two bottom covers are short in height and are notched to prevent incorrect insertion
-
The upper right cover is taller in height and is notched.
-
The upper left cover is taller in height and is not notched.
-
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the four 7 mm Phillips screws that secure the upper case to the lower case.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Flip the computer over and open the display.
-
Remove the two 4.5 mm Phillips screws securing the upper case to the lower case.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Wedge the flat end of a spudger in between the upper case and lower case near the bottom right corner of the display.
-
Carefully pry and rock the spudger upwards to create a small gap between the upper case and lower case.
-
Continue the previously described motion along the right edge of the upper case to release the clips securing the upper case to the lower case.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Repeat the same procedure as mentioned in the previous step to release the clips along the left side of the upper case.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Grasp the upper case and carefully lift it slightly upwards, freeing it from any remaining clips.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use your fingernail or the flat end of a spudger to flip up the retaining flap on the TouchPad cable ZIF socket.
-
Pull the TouchPad ribbon cable out of its socket.
-
Remove the upper case from the HP Mini 1000.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Pry the Wi-Fi antenna connectors (2 total) up off the Wi-Fi board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the single 3 mm Phillips screw securing Wi-Fi board to the motherboard.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Grasp the Wi-Fi board and lift it straight away from its socket on the motherboard.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the two 2.5 mm Phillips screws securing the heat sink to the motherboard.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Carefully lift the heat sink off the face of the motherboard and de-route the curved section from next to the fan.
-
Before reinstalling the heat sink, be sure to apply a new layer of thermal paste to the CPU. We have a thermal paste guide that makes it easy.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the flat end of a spudger to pry both antenna connectors up from their sockets on the Wi-Fi board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the flat end of a spudger to disconnect each of the following connectors from their respective sockets:
-
Speaker cable
-
Microphone cable
-
Fan cable
-
Power cable
-
Display data cable
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the single 5 mm Phillips screw securing the right display hinge to the lower case.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the two 5 mm Phillips screws securing the left display hinge to the lower case.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Lift the display out of the lower case, minding any cables that may get caught.
-
Annulla: non ho completato questa guida.
Altre 3 persone hanno completato questa guida.
Un commento
This was really helpful to me. My Mini's screen suddenly popped off on one side. After running through this process I found that both screws on one hinge and one screw on the other had come out. It seems someone forgot to put Lock Tite on them! Within less than an hour the machine was back to its usual self. Thanks!