Salta al contenuto principale

HP 15-ay052nr Screen Replacement

Cosa ti serve

  1. HP 15-ay052nr Screen Replacement, Battery: passo 1, immagine 1 di 1
    • To protect the device and yourself, make sure your device is completely powered down before disassembling. Disconnect all external devices before starting any tear down process.

    • Turn the device and lay it upside-down on a flat surface so the base of the computer is facing upwards.

  2. HP 15-ay052nr Screen Replacement: passo 2, immagine 1 di 1
    • Identify the two (2) sliding lock mechanisms on either side of the battery and slide them towards the center.

    • The sliders are located at the back of the device on the side where the display hinges are.

    • The slider closest to the optical drive (CD reader) clicks open but the opposite slider has a spring.

  3. HP 15-ay052nr Screen Replacement: passo 3, immagine 1 di 1
    • Pull the battery slightly up and out to remove.

    • If the battery doesn't pop out, the sliders weren't pushed in far enough. Push the sliders towards the center until the battery pops out.

  4. HP 15-ay052nr Screen Replacement, Bottom Cover: passo 4, immagine 1 di 1
    • Remove the rubber feet on the bottom of the device to access all the screws.

    • There are two rubber feet, one on each side of the battery compartment.

  5. HP 15-ay052nr Screen Replacement: passo 5, immagine 1 di 1
    • Unscrew the twelve 9 mm JIS #0 screws on the back of the device.

    • Gently remove the optical drive (CD reader) to more easily separate the base.

  6. HP 15-ay052nr Screen Replacement: passo 6, immagine 1 di 1
    • Unclip the keyboard surface from the base using an iFixit opening tool around the entire border.

  7. HP 15-ay052nr Screen Replacement: passo 7, immagine 1 di 1
    • Separate the base of the computer from the component assembly.

    • The optical drive can be placed in the base where it corresponds to prevent misplacing it.

  8. HP 15-ay052nr Screen Replacement, Fan: passo 8, immagine 1 di 1
    • Remove the two 6.5 mm JIS #0 screws holding the cooling fan to the base.

    • The base is the side by the heatsink, which is made of copper.

  9. HP 15-ay052nr Screen Replacement: passo 9, immagine 1 di 1
    • Unplug the fan cable from the motherboard.

    • The fan can now be removed.

  10. HP 15-ay052nr Screen Replacement, Screen: passo 10, immagine 1 di 1
    • Disconnect the display cable.

  11. HP 15-ay052nr Screen Replacement: passo 11, immagine 1 di 1
    • Unplug the wire attached to the wireless adapter.

  12. HP 15-ay052nr Screen Replacement: passo 12, immagine 1 di 1
    • Remove the two 6.5-mm screws from the fan side of the computer.

  13. HP 15-ay052nr Screen Replacement: passo 13, immagine 1 di 1
    • Remove the two 3mm JIS #0 screws.

    • Remove the one broad head 2mm JIS #0 screw.

  14. HP 15-ay052nr Screen Replacement: passo 14, immagine 1 di 1
    • Lay the display with its back on a flat surface.

  15. HP 15-ay052nr Screen Replacement: passo 15, immagine 1 di 1
    • Pry open the screen cover using an iFixit opening tool around the entire screen.

  16. HP 15-ay052nr Screen Replacement: passo 16, immagine 1 di 1
    • Remove the four 3-mm JIS #0 screws.

  17. HP 15-ay052nr Screen Replacement: passo 17, immagine 1 di 1
    • Unplug the cable connected to the screen located on the bottom.

    • The screen should come off and can be replaced.

Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 2 persone hanno completato questa guida.

0 Commenti

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 3

Ultimi 30 Giorni: 13

Tutti i Tempi: 391